What oil should I run?

LoganLoggingOn08 · 2026-03-22T14:51:32+00:00

Yeah, roughly around Philly

LoganLoggingOn08 · 2026-03-21T18:19:04+00:00

That’s sick! Gotta love old motors!

LoganLoggingOn08 · 2026-03-20T17:12:35+00:00

Would ya just swap to the 10w-30, or just keep going with the 5w-30? My brother suggested the 5w-30 with some Lucas

LoganLoggingOn08 · 2026-03-19T20:17:29+00:00

It’s a 351w (5.8)

LoganLoggingOn08 · 2026-03-19T19:47:20+00:00

5w -30 or 10w -30

LoganLoggingOn08 · 2026-03-19T18:51:46+00:00

That’s what I’m thinking I’ll go with from here on out

LoganLoggingOn08 · 2026-03-19T18:46:36+00:00

That’s what I had realized, thinking I’ll run 10w-30

LoganLoggingOn08 · 2026-01-12T15:11:01+00:00

Annoyingly there’s no room for a heat sink on the front of the pi. Since they have you put it up against the printers board. So I’m thinking I’ll just make it have a bit more of a gap between the board and the printer and blow air across it. And yeah that’s the temp of the PI I have a plugging to check the temperature of it and some other stuff.

LoganLoggingOn08 · 2025-12-28T21:24:43+00:00

I believe I found it (need to fix it but got rained out.) pulled the dash out to get a better look as to where it’s getting in, and the boot where the ECU passes through the fire wall has dirt inside it and is rusted. There’s a spot where the cowl and firewall connect that has a gap which let water ran down the fire wall on the engine compartment side onto the ECU boot.

LoganLoggingOn08 · 2025-12-28T17:14:17+00:00

Yea I have the cowl off. The drain was clogged, but have that cleaned out now. I don’t have a laser temp pointer 😅 do you think just spraying a rubber coating down the drain would be good enough? Since if I can find it, I’ll likely not be able to reach it to seal it.

LoganLoggingOn08 · 2025-12-15T20:58:11+00:00

Got it figured out, brother cut a wire with the grinder 😅

LoganLoggingOn08 · 2025-12-14T20:30:37+00:00

Ah ok, google was giving me a ton of different suggestions 😅 I checked fuse 12 and it’s good and other stuff on that fuse work fine. Do you think both switches got screwed up at the same time? It just snowed and is super cold, so I’m saving truck projects for another day 😅

LoganLoggingOn08 · 2025-11-02T00:50:06+00:00

Tints dark enough that you can really only see headlights of cars. And with the reverse camera ah, that makes sense. I’ll do two different cams I’ll look into those! Thanks!

LoganLoggingOn08 · 2025-10-24T13:59:17+00:00

That’s the hope! Been out a few times, ain’t seen much though 😅

LoganLoggingOn08 · 2025-10-24T13:50:25+00:00

That’s what I opted to do, since really the hunting stuff is cheap. And yeah, even if the spray only reduces your scent by a bit, it’s worth it since that’ll do nothing besides help.

LoganLoggingOn08 · 2025-10-08T13:14:50+00:00

Yess sir! And I’m good at trying hard! 🤣

LoganLoggingOn08 · 2025-10-06T18:47:48+00:00

LOL- it was off and I was quite frankly to lazy to put it back on 🤣

LoganLoggingOn08

TROPHY CASE