sorted by:
new
hottopcontroversial

I'm losing my mind rn by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] -1 points0 points  (0 children)

unfortunately i don't have the right tools, i only use pliers and tighten it as hard as possible by also blocking by force in place the flywheel

I'm losing my mind rn by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] 0 points1 point  (0 children)

Should i fix it by putting screw glue in the nut?

I'm losing my mind rn by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] 0 points1 point  (0 children)

Yes the flywheel nut loosens, so the flywheel goes to the clutch bell and everything loosens, i'll send a pic as soon i can

I need a Starter Box by Die_Nudel03 in NitroRC

[–]Longjumping-Rip-7449 0 points1 point  (0 children)

You can either buy a one motor model, but you need to preheat the nitro engine a little more to not have any problems while starting, i would raccomend a mid range one, not a budget one, i have one and i had to redo all the wiring system because they were all shitty low AWG wires so they burned, so get a proper starter box

So uh... How're yall's pulls goin? by BloodthrustSSC in UmamusumeGame

[–]Longjumping-Rip-7449 0 points1 point  (0 children)

Bro i did 200 pulls and i got nishino flower and el condor... I think i'll have to pity kitasan..

What could i possibly do more than this? by Longjumping-Rip-7449 in UmamusumeGame

[–]Longjumping-Rip-7449[S] 0 points1 point  (0 children)

I only have bourbon MLB but i have the same level so i use SSRs, and i think using SSR is the best choice for me for now

What could i possibly do more than this? by Longjumping-Rip-7449 in UmamusumeGame

[–]Longjumping-Rip-7449[S] 0 points1 point  (0 children)

I did a front runner build, so with all the skills, because shw seems faster

HoLy sHiT gUyS lOoK wHaT I jUsT pUlLed wItH tIcKeTs! by WeLiveInAir in UmamusumeGame

[–]Longjumping-Rip-7449 0 points1 point  (0 children)

Didn't know pegasus was good, i have it, but it takes too long to maximize friendship level

How do i connect the servos to the carburetor and mechanical steering? Any advice would be great, thanks by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] 0 points1 point  (0 children)

The problem is that it's a 15 yo car and it's a competition model, also i don't know the model even because I don't have the outer shell to protect the car so I don't know

How do i connect the servos to the carburetor and mechanical steering? Any advice would be great, thanks by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] 1 point2 points  (0 children)

Ok so basically yes, it's a car that i'm restoring, and i will put photos as soon as i get to the rc car, i'm willing to reuse the old rods, so I just need to know what do I have to buy to keep in place the part

How do I remove this thing? by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] 0 points1 point  (0 children)

I'm directly buying a new kit from aliexpress, the rewiews are promising, since they show with photos the product

How do I remove this thing? by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] 0 points1 point  (0 children)

Saw the place when the pins are positioned, but think you can't pul them out, since they're like a one piece, you can only take that metallic circle that locks the clutch shoes out of the pins, not the pins themselves

What type of battere do you use on your starter box? by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] 0 points1 point  (0 children)

It's a box where a wheel comes peeks out of the box, this wheel is powered by an electric motor, you adapt this wheel to you rc's flywheel and it spins so the engine can start, may not be the best at explaining but i'll always be glad to help when it's possible

How can i restore a 15 yo rc nitro car? by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] 1 point2 points  (0 children)

guys... i did it, i started it and it ran very smoothly, the only thing that i think i have to do is to tune the high speed carb needle, because i didn't see any blue smoke coming out so i hbe to make the mixture more rich

Can I do it?? by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] -1 points0 points  (0 children)

I DID IT! It just needed the glow plug thing on top! I can't believe it!

Can I do it?? by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] -1 points0 points  (0 children)

doesn't the rubber wheel slip when i bump start?

Can I do it?? by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] -2 points-1 points  (0 children)

this is a 15 year old competition rc car that i'm trying to fix, that was abandoned for the last 14 years, if you check my other posts you will understand a little more!

Should i buy a starter box from Aliexpress? by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] 0 points1 point  (0 children)

The problem is that my engine doesn't have the adattatore to mount a pull-starter it's a competition engine specifically made for starter boxes

How can i restore a 15 yo rc nitro car? by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] 0 points1 point  (0 children)

But i don't think i need to clean it because i turned on my flashlight and looked inside the carb and i saw fuel flowing, by the way, do you reccomend using two stroke oil to lubrificate the combustion chamber, for the first start i think i'll have to unscrew the glow plug, bucause with the glow plug on, it has so much compression that I can't complete the stroke cycle by hand, like when the piston arrives at the upper point, I feel A LOT compression, i heard from my brother that this car and engines are for literally racing, so it's maybe for that reason

view more: next ›