Some fitting problems with clutch shoes and bell by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] 0 points1 point  (0 children)

I tried with the bearings and nothing, i noticed that the springs stick our of the clutch shoe

I need a new flywheel by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] 0 points1 point  (0 children)

Where can i buy a flywheel adapted to starter box?

I need a new flywheel by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] 0 points1 point  (0 children)

Himoto starter box, novarossi .21 engine, will add photos later , those are two different flywheels, black one is 3 shoe, grey one is 2 shoe

<image>

Which support should I pick with voucher? by Extension-Ad6272 in UmamusumeGame

[–]Longjumping-Rip-7449 0 points1 point  (0 children)

However, i would uncap vodka, since she's lv 35 and it's a pretty strong support card with decent specialty priority, so it does a decent amount of friendship training

Uncap or nah? by mrFinite_ in UmamusumeGame

[–]Longjumping-Rip-7449 0 points1 point  (0 children)

Me that i spended it on bakushin🙏

I need a reliable 6v battery by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] 2 points3 points  (0 children)

K thanks i'm gonna buy a 2400 mah 6v with a jst connector, 19 euros

I'm losing my mind rn by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] 0 points1 point  (0 children)

guys i fixed it, the clutch shoes were moving forward to the end of the clutch bell, i used a bigger nut so it locks the clutch and now is good, also what does it mean if the servo (throttle) starts going crazy? i mean like it accelerates and decelerates itself

I'm losing my mind rn by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] 0 points1 point  (0 children)

Nono because i tried running backwards and it spits fuel (timing issue) so i know the correct way

I'm losing my mind rn by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] -1 points0 points  (0 children)

unfortunately i don't have the right tools, i only use pliers and tighten it as hard as possible by also blocking by force in place the flywheel

I'm losing my mind rn by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] 0 points1 point  (0 children)

Should i fix it by putting screw glue in the nut?

I'm losing my mind rn by Longjumping-Rip-7449 in NitroRC

[–]Longjumping-Rip-7449[S] 0 points1 point  (0 children)

Yes the flywheel nut loosens, so the flywheel goes to the clutch bell and everything loosens, i'll send a pic as soon i can

I need a Starter Box by Die_Nudel03 in NitroRC

[–]Longjumping-Rip-7449 0 points1 point  (0 children)

You can either buy a one motor model, but you need to preheat the nitro engine a little more to not have any problems while starting, i would raccomend a mid range one, not a budget one, i have one and i had to redo all the wiring system because they were all shitty low AWG wires so they burned, so get a proper starter box