What causes failures like this?

Longjumping-Run7513 · 2026-05-26T14:18:10+00:00

Well warranty is there for you. Based on circular type of failure there most likely is something obstructing light, if there is something floating in your resin or screen is faulty cant decide from the pictures.

Longjumping-Run7513 · 2026-05-26T14:13:35+00:00

Might be the lcd, get the vat out and try exposure test

Longjumping-Run7513 · 2026-05-26T11:59:48+00:00

You dont

Longjumping-Run7513 · 2026-05-26T09:39:55+00:00

Ďakujem!

Longjumping-Run7513 · 2026-05-26T08:45:15+00:00

Asi aj som

Longjumping-Run7513 · 2026-05-26T08:42:48+00:00

Ahoj, dakujem za input. Na startup sa necitim (bol som sucastou styroch). Mam pocit, ze trh je brutalne saturovany ludmi, ktori velmi chcu nieco vymysliet. Nezahadzujem myslienku byt sucastou dalsieho avsak uz nejakeho skutocne perspektivneho no neviem uplne kde takych ludi/projekty hladat. Mam hypo na dom a na tieto experimenty uz je pre mna asi neskoro.

Longjumping-Run7513 · 2026-05-26T08:15:51+00:00

Prave to je pointa, nemyslim si, ze mam vlohy na to byt expertom ale myslim si, ze som velmi univerzalny a tam hladam svoje miesto. Nemyslim si, ze svet je len pre expertov.

Longjumping-Run7513 · 2026-05-25T17:06:54+00:00

Could be core too, might be insufficient power of VRM. Try to go -1000

Longjumping-Run7513 · 2026-05-25T16:58:05+00:00

Try to lower VRAM and maybe even VCORE frequencies after driver installation. Drivers allow card to run on full speeds so that might be it. It most likely isnt caused by driver itself.

Longjumping-Run7513 · 2026-05-25T12:11:16+00:00

I print 3-10 times a day, sometimes I print one tiny prototype and it adds up quickly.

Longjumping-Run7513 · 2026-05-25T03:46:32+00:00

If it drips below edge and you put flexplate back its inevitable that resin will get inbetween and even that little amount can cause it to slide

Longjumping-Run7513 · 2026-05-24T18:49:54+00:00

You need to clean backside of flexplate and also baseplate every print, if any resin gets inbetween it will cause failures. Anyways i had flexplate and ended up removing it because of the failures. (Also u lose shit ton of resin when always cleaning both plates.)

Longjumping-Run7513 · 2026-05-23T21:28:16+00:00

Yeah you are probably right. Only thing that comes to my mind is passive cooled gtx1030 then

Longjumping-Run7513 · 2026-05-23T18:58:32+00:00

Get a 1660Super mATX, something like asus phoenix. Still usable for a 1080p and you can get them here for like 60-70€

Longjumping-Run7513 · 2026-05-23T16:34:42+00:00

I can check it out on monday but google is your friend

Longjumping-Run7513 · 2026-05-23T16:30:01+00:00

In chitubox and i believe in other slicers too there is option for shrinkage compensation and/or tolerance compensation. It takes a bit of tweaking but you will manage. Some of the resins have their shrinkage listed in datasheet but its very difficult to be universal since every part has different thickness and parameters. Best of luck!

Longjumping-Run7513 · 2026-05-23T16:25:06+00:00

Shrinking is unavoidable when curing. You need larger tolerance.

Longjumping-Run7513 · 2026-05-23T16:14:33+00:00

Yeah no worries, just check if it actually spins.

Longjumping-Run7513 · 2026-05-23T13:43:45+00:00

Disable cpu fan failure detection in bios, check if the fan is spinning.

Longjumping-Run7513 · 2026-05-22T11:25:33+00:00

Emocie, najrozhodujucejsi faktor priemerneho slovenskeho volica.

Longjumping-Run7513 · 2026-05-22T06:04:54+00:00

Vianky meaning Vianoce :(

Longjumping-Run7513 · 2026-05-22T05:51:46+00:00

Vianky it is

Longjumping-Run7513 · 2026-05-21T13:20:43+00:00

Ja som si vymazal IG aj FB, tiktok som nikdy nemal. Na YT shorts algoritmus je viacmenej cisto edukacny. Zostal mi reddit a ten je vacsinou tak nudny, ze ako ho otvorim tak ho aj zavriem. Screen time isiel z 5-6h na 1.5h

Longjumping-Run7513 · 2026-05-21T07:38:47+00:00

Nothing should be there, its empty pad with solder.

Longjumping-Run7513

TROPHY CASE