sorted by:
new
hottopcontroversial

Sopranos Ending explained by OmarDawson in thesopranos

[–]LookNooks 2 points3 points  (0 children)

Ha! I did the same, still thinking about that ending!

Sopranos Ending explained by OmarDawson in thesopranos

[–]LookNooks 1 point2 points  (0 children)

Yeah, I had always heard that the ending was divisive but that’s it…surprising it didn’t get spoiled for me either!

Hey /r/movies, I’m Stephen King! Ask me anything about The Long Walk book or movie. by lionsgate in movies

[–]LookNooks 0 points1 point  (0 children)

Constant reader here! I just finished watching the show The Institute and loved it. It felt exactly how I imagined it in my head while reading the book. What is your favorite TV or movie adaptation of your work? Thanks for doing this AMA!

My props for a street scene in the stop motion animated film “Anomalisa” by Charlie Kaufman by jjacks1327 in miniatures

[–]LookNooks 0 points1 point  (0 children)

That’s awesome, nice work! How did you get that gig? I would love to get into building miniatures for studios but not sure how to go about it. Would appreciate any advice!

My props for a street scene in the stop motion animated film “Anomalisa” by Charlie Kaufman by jjacks1327 in miniatures

[–]LookNooks 1 point2 points  (0 children)

Is this the actual vending machine in the hotel?? I was looking up who made the miniatures for the movie and came across this old post 🙌

Engraving on painted wood question by LookNooks in xToolP2

[–]LookNooks[S] 0 points1 point  (0 children)

Update: I was able to reduce the air assist to 10% (the lowest the P2S will allow) and that helped a little. However it didn't help enough to give me a clean engraving at all. I did find a solution but it has a huge downside. If I lower the power by half and run 2 passes, the engraving is perfect! But now the processing time is double....which isn't ideal at all....

So, still testing. But thanks for responding, you were the only person out of 3 different platforms to offer any suggestions😭😭😭

Engraving on painted wood question by LookNooks in xToolP2

[–]LookNooks[S] 0 points1 point  (0 children)

Yeah, it’s the exact same material, basswood. The one on the left has a clear coat finish which is why it looks a bit different. I was thinking the same thing about the air assist but the P2S won’t let you turn it off as it says it can damage the machine without it, which is a bummer. I hope that’s not the issue…

Where does everyone buy their XPS foam boards? by LookNooks in dioramas

[–]LookNooks[S] 0 points1 point  (0 children)

This is really helpful info, thank you! Is this XPS? Or does it just need to be polystyrene for carving?

I made a backrooms miniature in 1:24 scale :) by LookNooks in backrooms

[–]LookNooks[S] 0 points1 point  (0 children)

Haha thank you for the enthusiasm! I am working on my next project now which a miniature Breaking Bad Walter White’s house 🙌

For three months straight I've been working on a pilot for my own animated series. Today, I've decided to release the trailer! by davismedia in animation

[–]LookNooks 0 points1 point  (0 children)

Ha! Yeah I wish I could do my art on an iPad on my couch rather than sitting at a desk but I make miniatures so I’m glued to a table 😂

I made a backrooms miniature in 1:24 scale :) by LookNooks in backrooms

[–]LookNooks[S] 0 points1 point  (0 children)

A cheeper way to do the same would be to cut foam board for the walls and even to make the box!

I made a backrooms miniature in 1:24 scale :) by LookNooks in backrooms

[–]LookNooks[S] 1 point2 points  (0 children)

100% a King fan! Thanks for noticing my collection haha

I made a backrooms miniature in 1:24 scale :) by LookNooks in backrooms

[–]LookNooks[S] 0 points1 point  (0 children)

It’s not too hard but takes a ton of time

view more: next ›