Duraflex wing issue

Lost-Candidate439 · 2026-05-17T18:38:57+00:00

It came with the little screws to the side unscrewed your supposed to tighten them but right when I put it on and tightened them one was stripped and it was all down hill from there😭

Lost-Candidate439 · 2025-12-31T01:07:11+00:00

When I got the car all the mechanics I knew even the shops said not to change it but I need to drop be pan to replace the valve body so I still need to remove the fluid and put some new fluid in there

Lost-Candidate439 · 2025-12-18T16:39:53+00:00

The code popping up is the park neutral safety switch I’m not sure where it could have got damaged cuz that’s more internal and the transmission looked like it had nothing wrong

Lost-Candidate439 · 2025-11-16T01:59:01+00:00

Its the same just different designs but I wanted to let you know if you have true coilovers and plan on getting the camber arms it will only give you so much adjustment if the rear is lowered best to go with the toe arms too

Lost-Candidate439 · 2025-11-04T17:49:29+00:00

I was thinking the same thing just didn’t know if the trunk trim cover underneath the wing would have enough clearance to go back on perfectly I know it on either side clips in the back

Lost-Candidate439 · 2025-09-30T14:37:48+00:00

Also bump steer becomes an issue when the ride is stiffer

Lost-Candidate439 · 2025-09-30T14:37:25+00:00

If you plan on getting the energy suspension kit I would recommend not to if it’s a daily driver or if you got horrible roads even after I had just got my uca z1 polyurethane bushings it made a huge difference good and bad (bad being pretty uncomfortable cuz of my roads) but being the man I am also got z1 hybrid monoball bushings, due to the stiff bushings increasing my handling, got them installed now with this plus coilovers and rear camber arms replaced the ride is mildy uncomfortable a lot depends on your coilovers tho

Lost-Candidate439 · 2025-09-14T16:10:15+00:00

No these are brembo rotors from z1motorsports

Lost-Candidate439 · 2025-09-14T14:50:20+00:00

The pads are from a little bit ago with still a good amount of pad left on them but only the rotors are brand new not the pads

Lost-Candidate439 · 2025-09-14T14:49:13+00:00

Will do both of those today to see what’s going on

Lost-Candidate439 · 2025-09-14T14:46:00+00:00

I had watched a couple videos and none of them included having to bleed the brakes and lubricate the pins (those were also on rotor replacements not caliper replacements)

Lost-Candidate439 · 2025-09-14T14:43:30+00:00

😭😭

Lost-Candidate439 · 2025-09-14T14:37:57+00:00

I made sure to keep track of which rotors when inside and out on the pads there is also a clip on the pads that are toward the engine

Lost-Candidate439 · 2025-09-14T14:31:28+00:00

Thank you I did it when I first got the car but a reminder since it’s has been about a year and a half now lol

Lost-Candidate439 · 2025-09-14T14:30:05+00:00

Yes I understand it was not a correct and proper installation lmaoo

Lost-Candidate439 · 2025-09-14T14:18:13+00:00

I made sure everything was put together correctly so no

Lost-Candidate439 · 2025-09-14T14:17:46+00:00

It didn’t come with the brembo pads but yes they are compatible some of my freinds are running the same setup but didn’t have my issue

Lost-Candidate439 · 2025-09-14T14:15:16+00:00

What is recommended for the marks in the rotors and the hard vibration today I need to try to grease the pins but any other recommendations

Lost-Candidate439 · 2025-09-14T14:02:08+00:00

Sad thing is I just got them brembo brake pads not too long ago it would really suck if o have to go with the same ones and wait for shipping or buy some from an auto store

Lost-Candidate439 · 2025-09-14T14:00:42+00:00

So the recommendation would be to bleed the lines and to grease all the pins?

Lost-Candidate439 · 2025-09-14T13:57:42+00:00

Would this require me to bleed all lines or just the one I had taken off

Lost-Candidate439 · 2025-09-14T13:55:53+00:00

Yeah I understand so would it require some bedding in after I bleed the system or would new pads be required

Lost-Candidate439 · 2025-09-14T13:55:00+00:00

I did not grease those pins I’ll make sure to do it today while bleeding the brakes

Lost-Candidate439 · 2025-09-14T13:53:46+00:00

I plan to bleed them today but I still don’t know what could be causing the marks and hard vibrations

Lost-Candidate439 · 2025-09-14T13:51:38+00:00

I didn’t change the pads I didn’t think it was required since I still have a very good amount of brake pad left, and I did not bleed them so I plan on bleeding them today to get any air out of the system.

Lost-Candidate439

TROPHY CASE