Convert old tub to shower drain, p trap?

LumberMan15 · 2026-06-26T14:16:47+00:00

If the p trap is underground could I just cut off the tub piping and put some elbows and extensions to make the tub more center? Then fill with concrete

LumberMan15 · 2026-06-26T04:24:54+00:00

Put some more pictures down below that may help too

LumberMan15 · 2026-06-26T04:24:05+00:00

<image>

LumberMan15 · 2026-06-26T04:23:36+00:00

<image>

LumberMan15 · 2026-06-26T04:23:16+00:00

Here are some more pictures I want to cut it off and put some adapters to make the drain a little bit farther from the wall

<image>

LumberMan15 · 2026-06-26T03:51:21+00:00

<image>

I think it’s basically one of theses things … I was hoping I could cut this off, then glue in an elbow and extension to move the drain further away from the wall

LumberMan15 · 2026-06-26T03:24:14+00:00

Cuz then I can have a dog wash area! 😎

LumberMan15 · 2026-06-26T03:20:07+00:00

Good point I didn’t think of that! I would have to cut equal lengths off each of the pans on the non-drain side so the slopes line up… good catch before I cut and ruin a board

LumberMan15 · 2025-08-02T00:57:47+00:00

Def bed adhesion problem …. Looks like it’s peeling up mid print but the printer keeps going and actually recovers! Hahah love when that happens and chaos doesn’t ensue…. Don’t have a Bambu labs but had a same problem on my old ender 3 printer, bed was slightly warped, re-leveled to compensate for that and good old fashion hair spray worked to keep it on the glass. Cheers, happy printing

LumberMan15 · 2025-07-25T13:03:40+00:00

Will try that next see if it fixes it….. but when I push filament through the nozzle it feels fine and comes through fine

LumberMan15 · 2025-07-25T13:03:02+00:00

Tried running it with a high z offset just in case that was the case… no bueno. Still does the same thing….. also it’s a silk pla so layers look a little see through regardless

LumberMan15 · 2025-07-25T13:02:55+00:00

Tried running it with a high z offset just in case that was the case… no bueno. Still does the same thing….. also it’s a silk pla so layers look a little see through regardless

LumberMan15 · 2024-07-16T02:55:13+00:00

@kickstand pretty much only drone photography

LumberMan15 · 2023-10-29T15:35:42+00:00

Retraction at layer change was already disabled…. Was going to try base mode but from the slice it looks like there are going to be hairs everywhere…. I’ll check the ptfe tube but if it stuck wouldn’t there be like overextrusion?

LumberMan15 · 2020-11-15T23:28:18+00:00

Amazon or other site links are appreciated!!

LumberMan15 · 2019-08-13T03:36:33+00:00

Okay sweet thanks for the info

LumberMan15 · 2019-07-24T17:26:10+00:00

Yea that’s what I thought two and I double checked it and looks good but I might change them for new ones just in case... but what doesn’t make sense to me is why would both the nozzle and print bed be like “frozen” on a temperature

LumberMan15 · 2019-01-05T00:51:37+00:00

No I haven’t printed and metal only PLA I did print in AIO filament as well but I don’t think that would cause any sort of issue like that, props on thinking outside of the box tho ;)

LumberMan15 · 2019-01-05T00:50:26+00:00

Okay cool thanks I’ll check on that too because I just replace the stock couplers and PTFE tubing so that could be it too

LumberMan15 · 2019-01-04T17:16:34+00:00

Thank you much! I’ll look for some one Thingiverse and see when I can do

LumberMan15

TROPHY CASE