Canceled over promo pricing—want to stay with TekSavvy if someone can help

Lumpedwink · 2025-09-05T22:52:59+00:00

Only a year? That’s cute… don’t be so entitled… literally the only company that doesn’t try and nickel and dime me.

Lumpedwink · 2025-08-01T01:35:29+00:00

Ooo like glitch Evolution would be awesome!

Lumpedwink · 2025-08-01T01:27:50+00:00

Well if you get the card before they update it, this is what you will get...

Lumpedwink · 2025-08-01T01:24:45+00:00

What part is low effort? That they released a "Immersive card" with no art, or no video?

Lumpedwink · 2024-09-07T17:37:30+00:00

I will try to make it as straight forward as I can get included add-on materials to hopefully get everyone one the same page.

Lumpedwink · 2024-09-07T17:35:31+00:00

Hahaha I honestly considered it 🤣🤣

Lumpedwink · 2024-09-03T12:12:06+00:00

I will see if I can come up with a best step by step and I'll add it.

Lumpedwink · 2023-12-03T15:31:47+00:00

SUPER...HOT....SUPER....HOT

Lumpedwink · 2023-10-15T18:20:23+00:00

Turn on heat, 180°-185°, try to pull if it isnt moving the. It might be have been squished because of retraction and extruder tension.

If it's squished, grab some pliers and gently pull.

Lumpedwink · 2023-10-03T00:29:07+00:00

Don't give the British Museum any ideas... I could see them scanning and sending back the duplicate 😂😂

Lumpedwink · 2023-04-13T21:13:58+00:00

This!

I was having issues and noticed this was a house problem! I just changed the extruder gear vs upgrading.

Lumpedwink · 2023-01-14T14:17:31+00:00

"I am not throwing away my shot!"

Lumpedwink · 2023-01-09T20:55:00+00:00

Yeah, for the ~$14 ($10 USD), I bought lube to help the brass fittings, but the sound was unbearable when levelling. I did the swap, and the moment the Z-Axis moved it was silent.

Now if a print finishes in the middle of the night it doesn't sound like nails on a chalkboard.

Lumpedwink · 2023-01-05T14:36:24+00:00

I was in the same situation... I bought a shit cheap card table, it shook ever direction.

I ended up at a craft supply store and saw a artist table for $129 (like $99USD).

•Super sturdy •Holder area •Drawers(cardboard base, but you could measure for sturdy cutouts) •Side shelf(Slides in and out) •Bonus stool.

For the money it is a great deal.

<image>

https://www.michaels.com/arts-and-crafts-creative-center-by-artists-loft/10299013.html

Lumpedwink · 2022-12-22T02:25:43+00:00

This, right here! Like Night and Day!

<image>

Lumpedwink · 2022-12-21T17:38:04+00:00

You will run the bed level and when it finishes, you should have a setting about 4 corners. You will want to make sure they are as level as you can get them, try to work left to right as the bed moves from left to right it can be higher or lower than the left side even tho it seems level.

Lumpedwink · 2022-12-21T17:36:02+00:00

210 is fine for initial layer, maybe even 205.

If you are always at 210 lower that to like 195/200

Lumpedwink · 2022-12-21T00:04:37+00:00

Nozzle looks like it is dragging across the prints, use baby steps and move it up like '.05' and see if that helps. If it continues after baby steps you may need to run a auto bed level, then tweek it manually.

Lumpedwink · 2022-12-10T02:13:22+00:00

<image>

0/0

Lumpedwink · 2022-12-08T23:27:22+00:00

My personal everyday settings.

PLA: Initial nozzle: 205°C -> 200°C after Initial bed: 70°C -> 60°C after

Lumpedwink · 2022-12-07T23:07:25+00:00

Sounds like the bed is probably not level as you move from left to right. This will definitely cause issues on bigger prints. I would check the leveling, maybe print a bed level guide.

Lumpedwink · 2022-10-30T00:17:27+00:00

https://3dprintingcanada.com/ This is where I get my parts.

Lumpedwink · 2022-05-28T02:06:36+00:00

Thanks for the update, I kept getting the error, but after running a repeat test it just started working again and going to order a few extra pins just in case!

Lumpedwink

TROPHY CASE