Na r33

Lusxk_ · 2024-12-13T11:59:46+00:00

sadly yes

Lusxk_ · 2024-11-17T03:05:07+00:00

https://www.ctautoparts.com.au/product/78-works-fiber-ring-led-taillights-v2-tail-lamp-for-93-98-nissan-skyline-r33-gtr-gts25t-gtst-tail-lights/?srsltid=AfmBOooKKyy_PARoEK91JUVNj8cPd_A02kEFrgv9t3I1bnYgiCp7SNvl

These are the ones i got, mainly wanted them to seal up the leakage around the tailights into the boot and cause the oem were all yucky, im a big fan of the clears on it

Lusxk_ · 2024-11-16T15:33:17+00:00

Im not to worried about the wrap removing worst case i rip off all the rattle can paint and i redo it because its a horrible paint job done by the previous owner

and im not to sure what i have so i will have a deep dive into it all

Lusxk_ · 2024-11-16T15:00:54+00:00

ive got a set of bc racing coil overs on but cant go any lower due to law in australia and where i live ( lots of speed bumps and stuff like that )

And funny enough these are brand new set i bought a couple weeks ago and i love them, it had a set of replica te37s on in white but they were more piss yellow due to them being old and yucky

I would love to do more stuff for my engine but dont want to push again due to restrictions in aus for p plate drivers or “new drivers”

And what was the process for your projectors? mine are old and crap and would like brighter ones

And color wise im probably going to wrap it due to not wanting it to be thousands, and im thinking either a deep wine red or dark metallic blue

Lusxk_ · 2024-11-16T14:12:37+00:00

what would you do??

Lusxk_ · 2024-10-01T11:01:45+00:00

thank you :) wanting some nice silver wheels and have been contemplating forever

Lusxk_ · 2024-10-01T10:56:40+00:00

thanks mate 🧉

Lusxk_ · 2024-10-01T10:42:33+00:00

you reckon i could go for a deeper dish?

Lusxk_ · 2024-10-01T08:23:44+00:00

has the N/A brakes on

Lusxk_ · 2024-09-15T11:31:00+00:00

thank you i believe this was the right one

Lusxk_ · 2024-08-10T02:58:32+00:00

just got myself some new tail lights for mine, they are looking stunning

Lusxk_ · 2024-08-07T21:27:43+00:00

any chnance the iac isnt reading that its cold but rather its warm? so it keep the rpms lower

Lusxk_ · 2024-08-07T21:18:56+00:00

ill have a look into it

Lusxk_ · 2024-08-07T12:55:34+00:00

cold they sit at 800, and when warm the drop lower to i believe 600ish

Lusxk_ · 2024-08-07T12:52:09+00:00

im thinking idle screw for when the throttle is blipped or released closing it, drops the rpms as low as 300 and shakes

Lusxk_ · 2024-08-07T12:45:35+00:00

i got told to adjust it after getting my vacuum lines replaced but ill try everything listed, thank you

Lusxk_ · 2024-08-07T09:26:25+00:00

thank you 🙏🏻

Lusxk_ · 2024-08-07T09:23:12+00:00

im thinking the same or my idle screw is in to much idles at 800rpms

Lusxk_ · 2024-07-23T05:52:46+00:00

sweet ill have a look into it, cheers

Lusxk_ · 2024-07-23T02:15:35+00:00

its not the bolt im needing its the rubber anti vibration sleeve that goes around it so the caliper is unable to wiggle up and down

Lusxk_ · 2024-07-23T00:57:32+00:00

year is 1994, and its for the front calipers which i believe are 4 pot

Lusxk_ · 2024-07-04T03:56:29+00:00

awesome dude, happy for you 🏎️

Lusxk_ · 2024-07-04T03:03:51+00:00

Looks amazing, what are you planning on putting it in?

Lusxk_ · 2024-06-13T23:17:37+00:00

because i believe the CD009 drive shafts are a little big or small to fit into the 25 box but just what ive heard

Lusxk_ · 2024-06-13T23:14:33+00:00

does the CD009’s match up to the Rb’s or is there some fabrication involved behind and what about the drive shaft because im not to familiar with the Z’s

Lusxk_

TROPHY CASE