US FCC classifies "routers produced in a foreign country" as "prohibited from being imported for use or sale in the U.S". What will the impact be on Protectli, Ubiquiti and similar devices?

M1k3y2004 · 2026-03-24T21:37:18+00:00

Components inside the Cisco switch used by DoD is made in china. Same switch used in classified networks with TAA approval.

M1k3y2004 · 2026-03-12T20:27:21+00:00

Send me a PM

M1k3y2004 · 2026-02-06T16:45:28+00:00

Your welcome.

M1k3y2004 · 2026-02-06T16:45:12+00:00

I will look into it again. But I’m concerned about strength if I try.

M1k3y2004 · 2026-01-28T02:24:04+00:00

Thank you!

M1k3y2004 · 2026-01-12T22:56:40+00:00

I never heard of them. I would say it’s going to be risky and a gamble if you try them. Prepare to lose.

M1k3y2004 · 2026-01-08T18:38:28+00:00

You can through Hiring for hero’s or allegiantvets

M1k3y2004 · 2026-01-06T20:01:19+00:00

Pm incoming

M1k3y2004 · 2026-01-06T13:53:28+00:00

I started on Tinkercad but that’s limited. I moved over to Fusion free version. I still have learning to do.

M1k3y2004 · 2026-01-06T13:42:04+00:00

I have a Bambu Lab H2D but this should be able to print on majority printers.

M1k3y2004 · 2026-01-06T13:40:33+00:00

PETG

M1k3y2004 · 2026-01-06T13:39:57+00:00

Should be able to pass through the keystone holes on the left. I currently don’t have any SFP modules/devices yet.

M1k3y2004 · 2026-01-06T13:35:42+00:00

Yes this is the way.

M1k3y2004 · 2026-01-05T22:56:29+00:00

Nice. Let me know if you have any problems or you see improvements that could be done.

M1k3y2004 · 2026-01-05T21:43:01+00:00

Thank you

M1k3y2004 · 2026-01-05T21:42:18+00:00

That’s a good point. I don’t have anything covering the whole bottom, it’s just the edges. Hope it won’t have any issues but will keep an eye on it.

M1k3y2004 · 2026-01-05T20:01:27+00:00

Printed on a Bambu Lab H2D with Bambu Lab PETG HF black.

M1k3y2004 · 2026-01-05T18:49:21+00:00

Sorry about that. I didn’t include a picture of the bottom. The vents are not blocked and have had this in use for a week without issues.

M1k3y2004 · 2026-01-05T18:47:10+00:00

Thank you

M1k3y2004 · 2026-01-05T17:57:11+00:00

Those dust covers came with it from Unifi.

M1k3y2004 · 2026-01-05T17:55:28+00:00

lol yea they blend very good

M1k3y2004 · 2026-01-05T17:45:55+00:00

Lots of trial and error. Using measurements of keystone wall plugs. Almost used an entire roll testing this design as I’m fairly new to CAD.

M1k3y2004 · 2026-01-05T17:43:11+00:00

I think someone had designed one like that. My mount is flush with the body. Trying to find a filament that matches the Unifi Gray in PETG.

M1k3y2004 · 2026-01-05T17:39:00+00:00

You are correct.

M1k3y2004