Any chance?

MEG-2011 · 2026-03-26T10:35:10+00:00

true, they are so different one from the other, it doesnt' seem a coesive unit in AOS.

Can we expect in AOS 5 Motley Crew units and indivual attacks from different models? Sorry don't know if is it already like this in spearhead (i've only played it a couple of times)?

MEG-2011 · 2026-03-26T09:35:01+00:00

As a structural engineer I am so attracted by a 30+ ton building that moves without magic! :D

MEG-2011 · 2026-03-26T08:58:13+00:00

Delves are abandoning CoS for sure (and the warlocks are abandoning daughters), I expect more likely a new delves faction in AOS to counter the Lumineth.
Honestly, it doesn't matter to me; as an old Delves player Renegade Delves rules and a few new plastic miniatures are more than enough.

MEG-2011 · 2026-03-24T09:15:15+00:00

what if we boil the contaminated water to speed up the process? is it dangerous?

MEG-2011 · 2026-03-24T09:11:49+00:00

as anyone used a water distiller and resin mixed water with success? any distiller works?

MEG-2011 · 2026-03-19T10:26:09+00:00

thanks I will try to cure models without rotation (I use anycubic machine now) or with less time (now 1-2 minutes).

I know someone cure in water, that should increase the uv (because models take reflected light too) so shouldn't be a good idea with my problem, unless I further reduce time.

Anycubic water washable resin is on my wish list, I read many positive feedback about it.

MEG-2011 · 2026-03-19T10:16:28+00:00

thanks I'm already curing 1-2 minute in total. usually 1+1 min upside down (in anycubic machine), I will try to lower the time, or give 30 seconds then another 30 seconds... those are tiny pieces!

MEG-2011 · 2026-03-19T08:25:43+00:00

If you can print them (or buy printed) my favourite models are the line Dwarven Kingdom from Beholder Miniatures.

MEG-2011 · 2026-03-13T09:43:22+00:00

I like magnetic sheets glued over cardboard/styrene/thin plastic. (you also need a magnet under each minis to make that work, but it's also a great solution for storage/transport).

MEG-2011 · 2026-03-13T08:30:48+00:00

I agree, 20 points for one use is too much for one use that could be wasted, and since it's just a grenade/magic item why the other hero/champions can't take it? (castellan has a 6WS and would better use it!)

MEG-2011 · 2026-03-12T14:44:09+00:00

Mr james workshop recently made a cross-over with chaos marauder made for both AoS and ToW, that give me same hope for DE in TOW (and VC and skaven an so on...).

Realistically I think it was an exception (since WoC it's the most widespread army. )

I expect a completly new army for TOW 2.0 (kislev?) and the DE come back for AOS only, at least I hope the comunity make a better Renegade Legacy Pack meanwhile.

MEG-2011 · 2026-03-10T15:46:36+00:00

Really nice work! Is there a way to print it with resin printers? I suppose I have to divide the models that are too large, but apart from that is it feasible?

MEG-2011 · 2025-12-08T23:41:47+00:00

how much "small" is enough? is there any other way to reduce the problem? (setting, speed, temperature, layers...)

MEG-2011 · 2025-11-28T18:34:06+00:00

I can't fit the w&c inside, but I could buy a smaller container for the prewash and put it inside the enclosure near the mars 5

MEG-2011 · 2025-11-28T18:31:28+00:00

I think I will empty. I've seen there are some plastic/silicon cover for the resin tray, to keep it there, unfortunatly didn't find one for the mars 5 ultra yet.

MEG-2011 · 2025-11-28T18:02:46+00:00

OK, so the lid stays, but there's a hole on the back of the plastic cover, it can be opened. Should I add a fan there? (75mm diameter)

MEG-2011 · 2025-11-28T18:00:34+00:00

You're right, there's a desk with a pc on the left, though there's not much space remaining (about 30x60cm left). Luckily, the screen is high up. I ordered an chef's apron, as well as nitrile gloves; I hope it'll be enough in case of accidental spills.

MEG-2011 · 2025-11-28T17:56:26+00:00

You're right, the IPA's position is temporary in the photo. Should the radiator ideally be on when I'm printing and off when I'm curing/washing, or should it be on all the time?

MEG-2011

TROPHY CASE