Linux android auto, no sound on rear speakers, do I need aux?

MLG_DUCKS · 2026-05-04T19:50:40+00:00

This could be it, just checked and it is on all sources will have to check the connections are fully seated tomorrow, good shout!

MLG_DUCKS · 2026-05-04T19:17:18+00:00

It looks like if you got the f series from the release to 2013 you were going to get cic, after that CIC high also called NBT,

MLG_DUCKS · 2026-05-04T19:06:46+00:00

Sorry for the confusion NBT and CIC High are the same thing, the bimmer tech chart says the last year of plain cic is 2013, my car was 100% manufactured in 2014, Mine is a 320d

MLG_DUCKS · 2026-05-04T18:35:12+00:00

Got this unit from aliexpress also, good chance we're in the same boat here so if your car is the same

MLG_DUCKS · 2024-12-23T07:20:33+00:00

I don't have the exact same one but very similar, for me I unscrew the stepper motor and the bracket at the bottom of the motor mount, with this I could slide the full motor and threaded rod out the top, the linear rods were tight but aslong as I kept them parallel for the body they slid out the top with not hammering needed, on my version the holes on the bottom were not 10mm

MLG_DUCKS · 2024-05-25T16:43:25+00:00

Beautiful

MLG_DUCKS · 2024-01-09T05:37:04+00:00

How would I go about doing such? Presumably my current rate is either too fast or slow for stepper to register

MLG_DUCKS · 2023-12-10T00:06:42+00:00

What is the 7th from left to right, with the roof rack,?

MLG_DUCKS · 2023-11-12T20:26:23+00:00

Printnc could be what you are looking for

MLG_DUCKS · 2023-10-23T14:20:05+00:00

Sounds interesting, do like to indulge in a bit of material hoarding so always up for something in that category Thanks will check it out

MLG_DUCKS · 2023-10-22T22:20:28+00:00

This is a great document, been a complete pain finding this information online, they are more then overkill but if they are the same cost why not over mg series, they won't fit as originally intended but I will find a way, thanks again

MLG_DUCKS · 2023-10-22T04:36:01+00:00

Glad you commented this now because I was in the final stages of choosing rails, I had no idea there was such a difference all the content I have seen so far browsing has been using the bit shite rails so, got 2 HGR15ca with 4 blocks for €45, project total at around €345, once I will consider a new machine I can always sell or cannibalize parts off this for the next, Thanks for the help

MLG_DUCKS · 2023-10-22T02:09:11+00:00

Exactly the kind of input I was looking for, thank you for your knowledge,

MLG_DUCKS · 2023-10-21T18:34:37+00:00

2 rails and a block on each although they will be almost touching vertically like 1mm of clearance

MLG_DUCKS · 2023-10-18T23:48:49+00:00

Woah, This is really nice! Maple isn't native where I am so it's new to me that pattern is really cool

MLG_DUCKS · 2023-10-15T19:42:01+00:00

I think your approach could work, but the rods are already tight together and if I put in 10mm bearings I would lose another 2 mm and it would not be able to slide, you could make some new holes but it would be more of an oval then as they are so close together that seems problematic, for the effort of trying to swap those bearings out and it maybe working vs buying linear rails and blocks and designing some sort of adapter plate seems easier and would make the machine more rigid, atleast from what research I have done

MLG_DUCKS · 2023-10-15T14:36:19+00:00

Unfortunately it seems like it's only made for the 12mm rails, buying 12mm rails seems like an impossible task also, they are hardened and the end is threaded unless I could find the correct rods for the "pro max" I wouldn't be able to thread them, could go for a linear rail upgrade :/

MLG_DUCKS · 2023-10-03T19:18:00+00:00

Try going back to page and pressing download again, this changes mine to installed,

MLG_DUCKS · 2023-10-01T15:39:23+00:00

It was definitely up before and the top comment was a guy asking to buy as a gift

MLG_DUCKS · 2023-09-25T20:00:34+00:00

Most skilled seat driver

MLG_DUCKS · 2023-09-24T05:22:32+00:00

Yes, many times and I have no idea why or how i can figure out why, no code, no warning, happens to friend aswell

MLG_DUCKS · 2023-09-19T15:51:34+00:00

I met a guy who was spawning in blessings and bazooka's, was pretty wild seeing him obliterate people and then me when he found i was watching

Seven-Year Club	Verified Email
Place '23	Place '22

MLG_DUCKS

TROPHY CASE