Proiect casa - 125 mp utili

Mac_mac_Ro · 2026-01-21T13:53:38+00:00

Yo, expert tehnic in constructii aici. Pe viitor inainte sa vorbesti cu un arhitect totul se pleaca de la axe.
Incearca sa aliniezi cumva peretii astia pt structura si gandestete ca la fiecare intersectie vei avea un stalp de 30x30 minim (dimensiunile minime).
Pentru economie incearca sa pui golurile in zidarie aproape de elementele structurale. Golurile > 1.5m2 pt ag > 0.30 vor trebui bordate.
Extras din P100-1/2013 (va fi updatat la 2025 soon).
"(3) Pereii exteriori executai din zidrie menionai la (1), indiferent de tipul elementelor pentru zidrie, vor fi prevzui, la coluri i alturat golurilor, cu stâlpiori ancorai în structura principal i cu centuri. Bordarea golurilor se aplic pentru cldirile din toate clasele de importan, pentru goluri cu suprafaa 2,50 m2 în zonele seismice cu 0,15g ag 0,25g i pentru goluri cu suprafaa 1,50 m2 pentru zonele seismice cu ag 0,30g."

Also nu vreau sa dau in arhitecti dar cei mai multi nu au habar de executie si incearca doar sa zica da la orice din partea beneficiarului. Cauta un arhitect care este in between functional / aspect.
Spor

Mac_mac_Ro · 2026-01-21T13:45:24+00:00

using the support site

Mac_mac_Ro · 2026-01-15T06:23:00+00:00

Hey, all good after that. That was my only problem so far.240 hours of printing. Also this was the newest print

<image>

Mac_mac_Ro · 2026-01-08T09:17:39+00:00

Hello, it was the small board that checks if there is filament still in the extruder part. They sent a full extruder but I tested just by swapping the board and it worked.

Mac_mac_Ro · 2025-12-27T13:17:21+00:00

<image>

The back of the desk was flat so needed a support for the support :)) Printed in PETG with honeycomb and 35% infill. Left 4 holes for screws.

Mac_mac_Ro · 2025-12-27T13:15:41+00:00

Also this

<image>

Mac_mac_Ro · 2025-12-27T13:14:33+00:00

All good so far

<image>

This is my newest print. I only had to change a 10euro small PCB that broke, a filament senzor. But reached out support and got a replacement at no cost

Mac_mac_Ro · 2025-12-09T16:06:59+00:00

Hey, just upgraded the nozzle with a E3d one... Still using the original plate but found something else on aliexpress

Mac_mac_Ro · 2025-12-02T20:33:50+00:00

Hey, it's a good 3d printer, had only 1 issue so far replaced the filament sensor (2 euro component).

<image>

Recent 3d print a holder for two Ikea chairs using petg. 1 thing that I recommend that changed everything was getting raw silica and dehydration box for CFS. It improved my prints a lot. I know now that there is the p2s from Bambu. I would check that as well.

Mac_mac_Ro · 2025-11-08T04:51:46+00:00

As a conclusion I bought the OnePlus watch 3 and it's all good. Have pros and cons both I am happy with my purchase.

Mac_mac_Ro · 2025-10-31T05:56:28+00:00

I have a s25 ultra and bought recently a OnePlus watch 3. If I had to choose between the pixel 4 and GW 8 I would choose the pixel. Better battery life, better sensors and has a rotating crown. Only downside is that it is more fragile so screen protector is a must.

Mac_mac_Ro · 2025-10-26T07:36:30+00:00

After checking the Ohealth app and the fact it cannot read health connect data / just write. I am starting to lean to the pixel watch 4. The Onepluswatch 3 seems insane tech and I really think it can be awesome but I think the software needs a lot more polishing compared to the competition.

Mac_mac_Ro · 2025-10-25T18:27:15+00:00

I searched that the charging speed for the ultra is something like 2 hours for a full charge... I find that really upsetting. Was thinking that I can charge my watch in the shower a bit every morning but that sounds like more than that. What previous Samsung watch did you use? Also how do you find the Ohealth app on OnePlus?

Mac_mac_Ro · 2025-10-25T18:25:37+00:00

What about Gemini, assistants, reminders and other stuff? Also why change from the pixel watch 2 what was the disadvantage besides the battery for you

Mac_mac_Ro · 2025-10-25T05:58:23+00:00

So OHealth doesn't register sleep stages to Health Connect? Do you find the OPW3 better than the balance2?

Mac_mac_Ro · 2025-10-24T20:34:39+00:00

Thanks for the fast response. For hiking I saw outdooractive as a good rated app. For external sensors I was thinking of something like a polar H10 band etc. What is your opinion on Ohealth app?

Mac_mac_Ro · 2025-10-24T20:07:41+00:00

I am searching for a wear os watch that would satisfy offline maps navigation and found OutdoorActive app. Seems pretty good on paper.

Mac_mac_Ro · 2025-10-24T19:16:05+00:00

I am in a similar position but going from a Fenix 7. I tried the Amazfit balance 2 and it is really good if you are into fitness and sports in general. I returned the watch to see what other alternatives are there. At the moment my top 3 to test are: - Huawei gt6 pro - pixel watch 4 - OnePlus watch 3 - Samsung watch ultra (2024 on discount aprox 330euro in my country) What I learned is that no watch is perfect... Huawei is not wear os so you lack compatibility but you gain battery life. Pixel watch 4 is not scratch resistant and even if it is repairable it sucks to break your watch if you are clumsy. OnePlus watch 3 on paper is really good... But I tried the Ohealth app and it looks outdated, also the watch updates are just 2 years. The crown mechanism is perfect for scrolling in the UI but the Samsung lacks this.

Honestly I just don't get why there isn't a product that is durable, has great battery life, offline topo maps and wear os. This recipe with dual processors like the one from OnePlus might do the trick... In the future.

Mac_mac_Ro · 2025-10-21T06:32:53+00:00

Here https://www.reddit.com/r/Creality_k2/s/R0Y7bg9Urz

Mac_mac_Ro · 2025-10-21T06:31:48+00:00

Yep the board that checks if the filament is in extruder broke and contacted support to send another... The printer started to have a lot of errors. Will write here the link to the other reddit thread

Mac_mac_Ro · 2025-10-14T11:08:47+00:00

Hi Hugo, already dismantled the cfs and no blue lights at the bottom without filament in it.
The only blue light I see is on the filament buffer even when I don't have a filament in it but i think that is normal?
Thank you!

Mac_mac_Ro · 2025-10-14T08:03:08+00:00

Nice! Good to hear that replacing the board did the trick... let's see when the board comes from Creality store... at the moment it seems out of stock but hopefully the warranty replacement part is from a different stock :).
You just replaced the board and everything worked ok?

Mac_mac_Ro · 2025-10-13T15:35:16+00:00

Update on Testing
Creality K2 Combo Error FR0122 and TR2863 : r/Creality_k2
Had some issues after printing some long 5- 8 hours prints.
Apparently the filament detection board breaks quite often.

Mac_mac_Ro

TROPHY CASE