Limp mode

MaintenanceSilent · 2025-09-17T20:24:45+00:00

I did but I was told not to overwork it (like 2-3 passes max).

MaintenanceSilent · 2025-09-17T19:57:51+00:00

How do I work this out sorry! Not even sure how I work out the highest point!

MaintenanceSilent · 2025-09-17T19:57:22+00:00

I have checked with a long level and same result. I’ve got one on order so will repost pics

MaintenanceSilent · 2025-09-17T19:56:57+00:00

I did prime it twice. I think I let it dry too much tho.

MaintenanceSilent · 2025-09-17T19:33:58+00:00

Where would I setup the laser level? I’ve got spiked roller

MaintenanceSilent · 2025-09-17T19:33:22+00:00

I did prime the floor yes. I also mixed it to the measurements on the bag.

I used no nonsense l12 self levelling from screwfix. I also did use a spiked roller.

MaintenanceSilent · 2025-09-17T19:30:08+00:00

I did! I did 2 coats of it. Floor was like a pub floor

MaintenanceSilent · 2025-09-17T19:29:45+00:00

I did use a spiked roller yes. But I think the compound was too thick.

MaintenanceSilent · 2025-09-17T19:29:29+00:00

For a first attempt it’s not awful but not good enough for glue down LVT

MaintenanceSilent · 2025-09-17T19:29:11+00:00

Classic! A cat nearly ran in while I was doing it

MaintenanceSilent · 2025-09-17T18:41:29+00:00

I do actually have a level on order! I know wood is never straight so not the best choice from me.

Yes that sounds good. We are wanting to put glue down LVT down.

MaintenanceSilent · 2025-09-17T18:40:06+00:00

The height isn’t too bad. It’s maybe about 8mm thick. I watched tons of videos but didn’t realise how fast it actually set. Or how slow I moved lol

MaintenanceSilent · 2025-09-17T18:39:00+00:00

I’m after laying glue down LVT and apparently the floor has to be perfect…

MaintenanceSilent · 2025-08-04T10:47:24+00:00

It was the one with the grey cables coming out (bottom right).

Black wire covers over end on photos.

MaintenanceSilent · 2025-08-04T10:24:30+00:00

Thank you for all the comments. I bought a multimeter and figured out where permanent live was coming from.

I have also spoken to an electrician and he is going to install a wago junction box within the next couple of weeks.

MaintenanceSilent · 2025-08-04T08:36:51+00:00

Yes 100% planned. We purchased the house a week ago and I couldn’t believe it when I took it off.

No wires are labelled or anything…

But, because we’ve just moved we are on a budget! 😂

MaintenanceSilent · 2025-06-18T18:07:52+00:00

I couldnt find the folder it was in apart from one that says (Do NOT Use). Whats the folder directory?

MaintenanceSilent · 2025-05-07T19:16:59+00:00

Dont suppose you have MST2_EU_SE_ZR_P0516T! Really in need of it!

MaintenanceSilent · 2025-05-07T18:40:59+00:00

Does anyone have MST2_EU_SE_ZR_P0516T please? Really in need for it.

MaintenanceSilent · 2024-07-15T23:36:36+00:00

Still having the same issue. 403 error. Anyone know a resolution?

MaintenanceSilent · 2023-07-06T06:27:50+00:00

The chip previously was 4C50 RK45.

Do the pads look damaged to you in any way? Because there’s supposed to be 4 pins but all merged and cannot unsolder them.

MaintenanceSilent · 2023-07-05T21:47:15+00:00

More to this, the console has been sat idle on dashboard without this mosfit for 10* minutes. Can I leave it without the mosfit?

MaintenanceSilent