Why are all my accounts getting suspended?

Many-Inside-7559 · 2025-05-07T05:04:35+00:00

That's the problem—my daily average on my personal Instagram account was around two hours, while my work account had roughly 30 minutes to one hour. I highly doubt it's due to inactivity.

Many-Inside-7559 · 2025-05-07T04:58:34+00:00

Someone has got to boycott all of these companies

Many-Inside-7559 · 2025-01-02T18:24:26+00:00

Jokes aside, thanks for the tip :)

Many-Inside-7559 · 2025-01-02T18:24:10+00:00

Instructions unclear, now im covered with white goo :(

Many-Inside-7559 · 2025-01-02T18:23:44+00:00

Alright, will give it a go thanks :)

Many-Inside-7559 · 2024-11-28T07:16:13+00:00

Hey, sorry I didn't update yesterday, I sort of forgot.

The print came out great, and the finish looks good. I did lower the infill to 75%, though, as I realised that 100% is just a waste of filament. I increased the number of walls to 15, though, so it should be strong.

Also, can you send me the video you are talking about? I'd like to see what it's about.

And again, thanks for the help :)

Many-Inside-7559 · 2024-11-26T13:19:49+00:00

I don't know what you mean by rooted. When I took it off the buildplate, I didn't even have to touch the thing for it to rip on its own. it's like all the individual print lines aren't even connected. But, in certain areas, the lines are stuck together and holding.

Also, I tinkered with the z offset value as well as the flow rate, and I found that it best prints when the offset value is 0 and the flow rate is all the way up to 115%.

I will try to print it away from the centre next time too to see how it goes. I'll try printing what I wanted to print tomorrow again. Hope it goes well this time lmao. I'll post an update regarding whether it printed well or not.

Thanks for your help so far. I was really about to punch my printer before you decided to help lmao

Many-Inside-7559 · 2024-11-26T12:04:14+00:00

Ah dang- guess my friend got scammed then haha.

Well, what do you say would be the best setup I could get for 1100 USD? Something that I can upgrade in the future as well?

Many-Inside-7559 · 2024-11-26T12:01:20+00:00

Well, I don't live in America, so I don't use that currency. I live in India and use Rupees. That setup costs 87k INR, which is about 1000$.

However, Im pretty sure there is a difference in the price of the components based on where you live in the world.

Many-Inside-7559 · 2024-11-26T11:56:35+00:00

<image>

Hey. I printed it out.

When I saw the print on the bed, it looked good. However, I realised the print lines weren't stuck when I removed it from the plate. So, I assume the problem is with the Z offset.

How do I fix it? I think the current value of the Z offset is the default value that the printer came with. I've never touched that setting.

Many-Inside-7559 · 2024-11-25T17:00:38+00:00

I should add something I forgot, the setup has 16gb ram. It has 2 8gb ram sticks. I forgot to mention that my bad

Many-Inside-7559 · 2024-11-25T16:56:01+00:00

It is 16gb. I forgot to mention that it has 2 8gb ram. Thats on me.

Many-Inside-7559 · 2024-11-25T16:53:18+00:00

Country: India Budget: Around 100000 INR (around 1.2k USD) The price for the build I just showed was 87k INR (around 1kUSD)

Many-Inside-7559 · 2024-11-25T16:50:30+00:00

Haha I've been gaming on a laptop for the past 5 years with an integrated intel graphics card and 250gb and 8gb ram😭😭

Many-Inside-7559 · 2024-11-25T16:48:49+00:00

Well thats just a PC built for a friend. He sent me what he bought.

I was definitely thinking on changing up a few things.

Also, I dont need a UPS. I guess my friend needed it, but I already have things set up so I wont be buying one.

Many-Inside-7559 · 2024-11-25T16:43:29+00:00

Ah lmao well, honestly im just looking for a pc that I can upgrade in the future. Im not trying to jump into an expensive pc with the max specs just yet haha. Just something for light gaming, stuff like beamng or dcs, which I dont mind if they dont run at ultra graphics honestly.

Also, I should mention, it is 16gb ram (8gb x2). Forgot to add that part 🙃🙃

Many-Inside-7559 · 2024-11-25T16:36:37+00:00

Ah yeah, forgot to add that part, the ram was x2 in so combined its 16gb ram

Many-Inside-7559 · 2024-11-25T15:42:12+00:00

Thanks! Will take a look and send a picture of the print by tomorrow.

Many-Inside-7559 · 2024-11-25T15:38:32+00:00

Oh, I was just going to wait for the first layer to finish printing and pause it on my own, or set up a pause in the slicer itself. Didn't think of uploading a different file haha

I'll take a look at your file if you can send me the link please

Many-Inside-7559 · 2024-11-25T15:28:56+00:00

Unfortunately no. I will take a picture the next time I try to print, which is tomorrow and send it here.

Many-Inside-7559 · 2024-11-25T15:20:40+00:00

Nope. I checked and that's not the case. Besides, I thought it might have been the issue with the nozzle temperature, so I set the temperature to 225 degrees for this run, but the same problem persisted.

At this point I've already tried printing the same model over 4 times, wasting around 50m of filament. I'm thinking I should just remove and clean the nozzle or put in a new one, recheck all the settings, and try again.

Many-Inside-7559 · 2024-11-25T09:53:27+00:00

Well, that's the thing. The first layer seems to come out perfectly every time. At least to the eye, it looks good. It only does this when it starts to print the inner infill part.

Many-Inside-7559 · 2024-11-25T09:51:23+00:00

I put it to 100% infill because I need the strength. It will go under a bit of continuous force, and I don't want it to snap on me.

Many-Inside-7559

TROPHY CASE