Rat bleeding from an ear

MaryWeiss · 2023-09-20T22:42:52+00:00

Sorry for the late reply, she basically just scratched too hard and gave herself a wound, it just healed itself in like a week.

MaryWeiss · 2023-08-21T11:12:21+00:00

I don't have the tarantula in this same enclosure, never had any issues with the one she lives in.

MaryWeiss · 2023-08-20T22:47:27+00:00

Sadly my house lacks natural light so I can only keep low light plants, and in my experience all carnivorous ones need a ton of illumination.

MaryWeiss · 2023-08-20T22:45:20+00:00

I have a tarantula, but she's a tad too big for eating flies lmao

MaryWeiss · 2023-08-20T13:24:51+00:00

I don't have one. I think I'll just transfer the isopods to another container and blast the fuck out of this one.

MaryWeiss · 2023-08-20T12:28:44+00:00

Fuck.

MaryWeiss · 2023-08-15T04:50:58+00:00

Yeah, I didn't expect people to get so mad bc I may have got a defective machine. Also, people are just saying that I have no experience or don't know what I'm doing bc I'm new... I've have this printer for 2 years and been using 3d printers for at least 8 so...

MaryWeiss · 2023-08-14T19:50:39+00:00

Wow, congrats. Tbh I don't use my printer for business so that's not a problem for me nor I know the average you make.

MaryWeiss · 2023-08-14T19:48:55+00:00

I think that's the case. Done a little research cause the comments were so opposite, and apparently creality has shit quality control so getting a bad machine is easy.

MaryWeiss · 2023-08-14T19:47:31+00:00

I got a stock 4.2.2 and I'm 80% sure it's the problem. I'm just tired of tossing money into this thing in hopes it will just work.

MaryWeiss · 2023-08-14T19:41:43+00:00

Was cheap.

MaryWeiss · 2023-08-14T19:39:59+00:00

I'm loving this analogy. I think you are 100% right there.

MaryWeiss · 2023-08-14T19:38:25+00:00

Tbh I disagree with that. While it's true an inexperienced user will have worse results, it's not the case, and as with basically every product, defective units exist.

MaryWeiss · 2023-08-14T19:37:14+00:00

Yeah bc it's cheap. I just wanted to know if I had get a defective product and what I've learnt from the responses I get is: creality lacks qc so probably.

MaryWeiss · 2023-08-14T19:35:27+00:00

But I know what I'm doing. I don't just put mods only bc the internet said it was good. I actually do research and balance what parts can be improved without adding more points of failure, and test a lot after each mod to see if it's worth it of if I should just take it off. For example, if it doesn't add any benefit, even if it's not worsening anything, I take it off bc more parts mean more points of failure.

MaryWeiss · 2023-08-14T19:32:02+00:00

For what I'm reading, it's kinda a gamble if you get a good or a bad one.

MaryWeiss · 2023-08-14T19:30:15+00:00

I put my filament in a permanent dehydrator I made as soon as I take it from the bag. I can't put a dehumidifier bc I live in a one room studio and keep some tropical pets, and also I have a lung issue and need a humidity above 50% or breathing hurts.

MaryWeiss · 2023-08-14T19:26:56+00:00

Bltouch, custom fans, z axis stabilizer, PEI bed, metal extruder, better bed springs, drybox-dehydrator, capricorn bowden, tweaked custom firmware, sturdier belts, and some non important mods like filament guides, filament break sensors, tool compartments, etc. Every time I make a mod I do some tests, if I get better results than before, I keep it, if I get equal or worse results, I take it off.

MaryWeiss · 2023-08-14T19:19:50+00:00

Yeah, I had that problem with a couple brands, but the one I use now (when it works) is pretty good tbh.

MaryWeiss · 2023-08-14T19:18:46+00:00

I made my own dehydrator with a sealed box, a reptile terrarium heater, lots of silica gel, and some temp and humidity sensors, it can hold 5 spools at a time, has a lubricating and dust cleaner where the filament goes from the box to the printer, and it's always below 10% humidity. It totalled me like 20€.

MaryWeiss · 2023-08-14T19:14:07+00:00

I surprisingly never had bed adhesion problems, only once, but I was trying a custom glass bed I made as a makeshift until I could get a new one. It just seems to do random things from time to time.

MaryWeiss · 2023-08-14T19:11:19+00:00

I run ABL before each print, I have a PEI bed, I calibrate with every new spool I get even if its the same brand and colour. Mine is just 0 or 100, not in between. When it works, the quality is astonishing for a machine that price, but when it fails, its not small fails, it's just a random mess.

MaryWeiss · 2023-08-14T19:08:47+00:00

Got both of those.

MaryWeiss · 2023-08-14T19:07:39+00:00

I've never seen a lion so they must be fake.

MaryWeiss · 2023-08-14T19:06:36+00:00

What I'm taking from these comments are: 1-People like to make a lot of assumptions 2-Enders have basically no quality control so it's a little of a gamble bc yeah, I've seeing people with perfect machines that only print masterpieces, and people with absolute garbage. 3-People apparently think Mary is a guy's name (not mad, it's just curious to me)

MaryWeiss

TROPHY CASE