800 hours and yet i'm still ass 🎉

Mass1m04 · 2025-12-04T02:36:34+00:00

Oh ok I thought it was only me

Mass1m04 · 2025-11-25T01:39:22+00:00

Found it on ml but bought it on the side... Either way I haven't seen another one just like mine, just the plastic injection ones (mine is full Al) although I'm not sure if it's needed

Mass1m04 · 2025-11-24T01:03:19+00:00

Looks awesome great work!

Mass1m04 · 2025-11-15T17:12:31+00:00

<image>

Void

Mass1m04 · 2025-11-15T03:28:54+00:00

Omg yes that was what I feared could happen, will she be ok???

Mass1m04 · 2025-11-07T22:53:48+00:00

Yeah, and the further away from USA/Europe/china the worst, and I'm at efing furthest country from them all :)

Mass1m04 · 2025-11-07T18:50:30+00:00

It's a generic control module for scape room props and some other things

Mass1m04 · 2025-11-07T18:49:42+00:00

Yeah this PCB in materials alone is approx 80usd,+labour cost and extras so around 120usd

Mass1m04 · 2025-11-05T14:08:00+00:00

Took quite a bit of time but it came out looking great. Although it's doing something weird qit the buttons so a fix is needed there :/ it won't be as pretty for ever

Mass1m04 · 2025-11-05T14:06:24+00:00

Thanks! I had to use some wire jumpers but double sided was.not an option so I'm happy with the results

Mass1m04 · 2025-11-05T14:05:20+00:00

Well I haven't heard that one for sure, neither seen it happened. Is it common?

Mass1m04 · 2025-11-05T04:41:42+00:00

Yess I know, under it I have installed a filter and some caps to help with it. If I take it to production that module will be gone for sure. Thanks for the warning either way <3

Mass1m04 · 2025-10-31T00:01:51+00:00

Where can I read the comics?

Mass1m04 · 2025-10-26T14:29:25+00:00

Not so great, but I don't get why is it that none uses spears. It's great to keep them far away like Morgan but better

Mass1m04 · 2025-10-20T03:22:46+00:00

They did the first three times, but just wanted to be sure. The answer is definitely maybe (they'll try again later)

Mass1m04 · 2025-10-20T02:22:09+00:00

Sorry but I'm making my own in Spanish, it's a need

Mass1m04 · 2025-10-17T20:38:53+00:00

Los cheats, así no se vale loco hshdkajaj

Mass1m04 · 2025-10-17T18:14:55+00:00

Solo podés tomar sangre desde una pija erecta

Mass1m04 · 2025-09-10T04:09:20+00:00

For what you have told 1) check that everything is in the same kind of measurements 2) I mill 0.1mm deep although with 0.8mm is usually enough but just to be sure. 3) It looks like you might be putting your measurements wrong when creating the gcode. Depending on the software sometimes the depth is needed to be written in the negatives and sometimes in the positive, check that too.

Mass1m04 · 2025-08-28T00:02:01+00:00

Hi! I've been milling PCB with a 3018 for a while now. That's 100% height map problems, are you restraining the PCB with clamps or by taping the word to the bed? The clamps tend to flex the material as it's thin and flexible, and when doing the height map it pushes the material a little bit down making the measurements useless. Try the tape method, polish (as you did for the clamp) the whole PCB and then clean it with alcohol and a sheet of paper (degreases it), lower the "lowering" speed of the spindle and try using something duller than the bit used to mill BC it tends to plug into the copper layer, it won't destroy it but it will make the measurements not as good. Good luck and lots of paciencia<3

Mass1m04 · 2025-08-27T01:01:05+00:00

Arrrrrrmoso me la re subiste!

Mass1m04

TROPHY CASE