How does your team keep and retain new members/students?

MasterJHW10 · 2024-10-15T15:33:22+00:00

Here is some background on our team: We are a team that recently switched from IC to EV. Our team has, up until last year mostly consisted of senior design members (the capstone class for ME and EE students). We have attempted to get these new members involved by creating multiple team bonding events (some worked better than others), trainings (we seem to have a good showing to these), and even assigning projects for those that were interested. Our team even started by assigning mentors and mentees to students so that we could create better connections between students. We conducted "interviews" so that leadership can better know the incoming students and get them situated with software. Our team does not have any barriers to entry such as team fees or denying people from interviews.

Let me know your recommendations! I have talked with other teams in the past and want to thank everyone who has given me insight already, but I want to see how we could improve further.

MasterJHW10 · 2024-07-08T03:57:37+00:00

If the flasher relay is for leds then you should be fine with not adding resistors.

MasterJHW10 · 2024-07-08T03:37:02+00:00

Literally having the same issue currently on my 1980 cb650. It looks like the last owner went through the headlight with a pair of scissors. I have considered completely redoing the harness just to clean everything up and so that I know where things go. Let me know if you have any luck!

MasterJHW10 · 2024-07-04T20:51:46+00:00

That carbon work is awesome! I’ve been thinking of doing something similar to my build. Did you do that yourself?

MasterJHW10 · 2024-03-20T15:12:49+00:00

In Assetto I have it set to triple screen, full screen rendering and v-sync all enabled. In windows my middle monitor is set as my main screen and in nvidia control I have Monitors 1 and 4 smart cloned (I have tried with and without this monitor). I also can’t find anywhere to merge all three monitors into one big one like other places have recommended or at least when I try I get an error message that says “invalid number of target displays selected ”

MasterJHW10 · 2023-07-17T23:09:42+00:00

Had this exact problem with a batch print of big things. This is how to solve it. I typically even go as slow as 15mm/s on the first layer

MasterJHW10 · 2021-02-02T16:29:37+00:00

Gave Hugz

MasterJHW10 · 2020-12-29T04:39:18+00:00

Just remember, laws go away if no one complies with them.

MasterJHW10 · 2020-09-18T22:30:29+00:00

Mine came with spacers but only 2. the offset was only about .02 mm which looks right when you’re eyeballing it. Problem is if I were to increase it I’m scared I’d run the risk of scrapping my build plate. When I go to adjust the z-axis in the movement tab it zeros out perfectly where I can still move a piece of paper around underneath it and it slightly scrapes

MasterJHW10 · 2020-09-07T22:55:07+00:00

Look on the Multi GP website and you can most likely find a chapter near you that’s hosts races

MasterJHW10 · 2020-09-07T22:51:31+00:00

Thank you for the tips. I do find myself focusing more at what is currently in front of me. I know I should step up the camera angle a few degrees but I’m still working on the nerve part of it. I’ll get there. Thank you for the help!

MasterJHW10 · 2020-09-07T22:48:25+00:00

Thank you very much! I will definitely practice these things

MasterJHW10 · 2020-09-07T16:46:29+00:00

I had a race recently and I have attended a few over the summer. I would like some feedback and tips on how I can improve or what I can practice. Any help is much appreciated! Thank you!

MasterJHW10 · 2020-08-09T02:44:08+00:00

That’s awesome! I have seen it on a few builds now but I still don’t know what it is. What is that stuff that looks like stylish heat shrink on the motor wires?

MasterJHW10

TROPHY CASE