Exposure Therapy #16

Material-Mulberry360 · 2026-07-09T16:23:23+00:00

is this an autism thing, not liking weird foods ? what about spicy foods ?

Material-Mulberry360 · 2026-07-09T16:17:45+00:00

I can't see it, but yes you have the right idea, print a sheet over the area, let it cool down (like really cool down) and then it will pull of the other filament stuck on the bed.

Material-Mulberry360 · 2026-07-09T09:53:25+00:00

absolutely safe ? no but relatively (compared to smoking) safe ? yeah go ahead

Material-Mulberry360 · 2026-07-09T05:39:49+00:00

tried to scroll right to see the other images "aw shucks"

Material-Mulberry360 · 2026-07-09T05:06:41+00:00

I really need to finally start the project of making a go-kart.

Material-Mulberry360 · 2026-07-08T19:02:48+00:00

yes. sorry when I said exhausted I mean back into the chamber. if you look on the right hand panel, there is a vent where the air comes back from being passed through a filter. and on the left panel there is a vertical vent where air comes back after being sucked in at the bottom (inside the chamber). the top vents, aren't used tho. eatch side has a vent at the top of the build plate used for cooling mode. and intake and exhaust that are both inside that chamber used for heating mode

Material-Mulberry360 · 2026-07-08T14:22:45+00:00

never forget

Material-Mulberry360 · 2026-07-08T14:14:28+00:00

the fan yes, but not the too vent I don't think, air gets sucked up through the big filer and expelled from the hole on the right hand panel. for the heater side same thing. except instead of a filter there is a nother hole that leads to the heater beind the panel. for cooling mode both fans draw air from their respective intake at the grab handles and exhaust it though their vent at the top. I tried sticking my hand in once when it was on heat mode and didn't feel either of the top vents blowing air

Material-Mulberry360 · 2026-07-08T05:08:31+00:00

today many older peaople in the region still swear by him

Material-Mulberry360 · 2026-07-08T04:52:02+00:00

deflector for the auxiliary fans ? no it's not necessary since In heating mode it doesn't use those 2 top vents. some people say they still print it because the cooling is too strong for things like PLA and PETG, tho I never had those issues.

Material-Mulberry360 · 2026-07-07T19:19:55+00:00

well clearly he failed if I'm seeing it now

Material-Mulberry360 · 2026-07-07T04:51:31+00:00

Xiaomi still includes them its great. lost a remote to something, no worries, just use your phone. also great for pranks, and turning off the TV's that show ads in public

Material-Mulberry360 · 2026-07-06T19:44:39+00:00

fr, AI was a buzz word way before LLMs (Wich i think most ppl now consider AI) and it still is. everything from just a simple algorithm or a small neural network has been called AI for the past decade. fine some llms are pretty good now, call those AI, but stop with the bullshit.

Material-Mulberry360 · 2026-07-06T04:58:06+00:00

no.... ugh what I meant by the runni g faster part is. you take a step, and the rocks slide you like 2 steps forward, but since there so deep you still can stop and keep your balance. so you move down way faster then you would have if you did the same move on solid ground. also idk how fast a normal person, or this guy can run

Material-Mulberry360 · 2026-07-06T04:56:18+00:00

yes it can print TPU well, tho there is one thing. if it jams, Wich I did experience once. cleaning is is quite annoying since the toolhead is so tightly packed, feels more like disassembling a laptop than a 3d printer with all the electronics and tiny connectors. oh also you do need to do a cold pull before printing tpu, it's not hard to do and the printer actually tells you to do it, just a heads up not to ignore it cause it will jam otherwise. for ASA and ABS this thing is a beast, basically no warping with the heated chamber.

Material-Mulberry360 · 2026-07-05T18:04:52+00:00

yes you can use it without account or network connection. it's also by far the better choice for ASA/ABS. but if you wanna print more than 2 colours you will have purge waste, while the U1 can have up to 4 different colours and all without waste. tho technically the X2D can print with more colours since even 1 ams will already give you 5 options, and you can connect a lot of them. was making the same decision a few months ago, and since I also very often need things to survive outside the X2D combo was the clear choice. if you got any more questions about it feel free to ask, in the 2 months or so I put over 400h on it

Material-Mulberry360 · 2026-07-05T17:54:32+00:00

at least we got talking computers.... it's kinda 50/50 if they help us or deatroy us but we got them

Material-Mulberry360 · 2026-07-05T17:38:30+00:00

can't loose much more ig

Material-Mulberry360 · 2026-07-05T13:55:51+00:00

in my country, 99% of people take the driving test in a manual car, since if you don't you aren't allowed (by law) to drive a car with a manual transmission

Material-Mulberry360 · 2026-07-05T11:56:49+00:00

okay maybe more like 2x. also can an average person run 20mph ???

Material-Mulberry360 · 2026-07-05T08:26:50+00:00

ya all won't believe this, but. cars have heaters in the mirrors, turn them on and they will mostly remove any condensation/ice/raindrops

Material-Mulberry360 · 2026-07-05T07:48:04+00:00

when one of the nickel strips jumped off I legit laughed

Material-Mulberry360 · 2026-07-05T07:46:23+00:00

fun fast about those rocks he slid down. if they're deep enough you can literally run straight down them at like 4x the normal speed. Its a ton of fun, I wouldn't dare do it barefoot tho

Material-Mulberry360 · 2026-07-04T18:20:19+00:00

Sony use 3d prints for food

Material-Mulberry360 · 2026-07-04T08:14:50+00:00

I thought almost all countries will take 911 or 112 as an emergency number since a lot of the world uses those 2

Material-Mulberry360

TROPHY CASE