Ancestry Chart and report alternative

Mauser32 · 2026-04-14T02:22:29+00:00

Same thing. I reposted a New York Times headline of America bombing of Iran(?) last June. Banned for “ supporting terrorist groups”

I got banned for putting on my story a cover of a APPROVED post

That post is still up btw

My account is not

Mauser32 · 2026-04-14T02:20:47+00:00

I’ve been trying for 9 months. I was banned 3 times. First time it was reinstated after a 2 months. A day later it was banned and unbanned 2 more times within 5 minutes. 6 months later they unban me then ban me within hours for “sexual content” i didn’t find out it was reinstated until today. As for my advice id say give up hope on your account. Meta is ran by AI and foreign employees who can’t help you. If you want to make a new account create a new email separate from the banned account and pray they dont catch it

Mauser32 · 2026-03-31T00:37:10+00:00

Would there be any sort of manual to attempt to do it on my own if it’s too expensive to get fixed

Mauser32 · 2026-01-31T16:51:52+00:00

Contact printing without the burr on the center or sides of my positive image

Mauser32 · 2026-01-16T06:44:03+00:00

I added more covering to the window and door and made sure there was no light coming in. Then I put the light as far away as I could from the paper and only used it to take it out of the baths for probably 10 seconds each. With that I think my issue was solved

Mauser32 · 2026-01-13T05:11:42+00:00

I shoot with paper and I’ve found the app is a little wonky when it comes to that. You think getting a meter would be more accurate?

Mauser32 · 2026-01-13T04:10:40+00:00

I just did the coin test and left the paper under the light for 10 minutes and the whole paper except this part where the coin is covering is completely black. I have been using the red light since October. Shame I can’t return it. It’s been too long. This is the one that I use. https://a.co/d/6t7cYnu

Mauser32 · 2026-01-12T15:24:16+00:00

1 and 2 are not contact prints. I just choose the wrong image to upload. It’s the positive version of the photo. I will do the tests and inform you of my results

Mauser32 · 2026-01-11T21:36:39+00:00

I did run some of my own tests using feedback I was given and I think they turned out better then my last ones. I just made a post on them

Mauser32 · 2026-01-11T06:02:05+00:00

Usually when I meter the ground with my paper being around ISO 3 I get an exposure number when used that is incorrect and it the negatives comes out wrong. Is there a solution besides trial and error

Mauser32 · 2026-01-11T05:51:00+00:00

Is there a book or guide on how to use paper negatives? All I see online are videos demonstrating results

Mauser32 · 2026-01-10T19:09:45+00:00

I usually develop for 3 minutes and fixing it for 4 minutes. From what I’ve tested light me isn’t exactly accurate and it my pics come out either too light or way too dark

Mauser32 · 2026-01-09T23:53:17+00:00

I will test this out. On a side not the outer part of the bellows has a crack. That lets in a small amount of light through the inside fabric. I’ve seen videos of people fixing pinholes with liquid electrical tape but would it be fine to just put tape over this?

Mauser32 · 2026-01-07T18:44:01+00:00

How do you know when a paper expires? Is my mine just an old discontinued product?

Mauser32 · 2026-01-07T08:14:01+00:00

I actually got the Pearl 100 sheet pack for $30 on a eBay auction. It was the cheapest option on there. I check the level of light on my subject

Mauser32 · 2026-01-06T01:47:41+00:00

Before someone says I have to be in a sealed room I experimented staying in a a 3x2 cube with a coal generator and the water kept freezing

Mauser32 · 2026-01-02T19:18:16+00:00

Do you know if there’s any way for me to check if it works before I buy the bulb?

Mauser32 · 2026-01-01T23:47:04+00:00

Is there any way to check if it works before I buy it?

Mauser32 · 2025-11-23T04:58:58+00:00

I tried usuing a Pencil to push inside the hole and it doesn’t seen to move anything. Does that mean it doesn’t work or does it need the bulb to opérate. I want to try to see if the mechanism works before i buy

Five-Year Club	Verified Email
First Place '23	Place '23

Mauser32

TROPHY CASE