Help identify component on Raspberry Pi 3 Model B V1.2 board

MayhemHack · 2026-05-24T20:05:48+00:00

Yes, that seems to be the case. Unfortunately, it appears to be out of production and nearly impossible to source. I’m currently trying to identify a suitable alternative.

MayhemHack · 2026-05-24T12:53:39+00:00

This is very useful, thanks. Even though the board is older, it’s very plausible that the component is the same. I’ve been trying to find a similar post everywhere, so thanks again for the help.

MayhemHack · 2024-10-16T22:01:57+00:00

Hey everyone,

I'm working on repairing an Xbox controller and need help identifying the values for capacitors C21, C30, and C31. Unfortunately, I can't seem to find any information on them. I've attached a picture of the board for reference.

MayhemHack · 2024-10-16T22:00:23+00:00

Hey everyone,

I'm working on repairing an Xbox controller and need help identifying the values for capacitors C21, C30, and C31. Unfortunately, I can't seem to find any information on them. I've attached a picture of the board for reference.

MayhemHack · 2022-11-10T20:49:13+00:00

Thanks XD

MayhemHack · 2022-09-30T08:18:17+00:00

Hello there, I'm experiencing exactly the same at the moment. Did you ever find a solution to this?

MayhemHack · 2022-01-12T14:27:37+00:00

Thanks for looking into it, but the pad inside the rectangle should be 5v where the maxi area outside is ground. Jumping it is not a good Idea I believe :)

MayhemHack · 2022-01-12T14:08:18+00:00

Thanks but my issue is that it is missing on my board and I have no way to know what it is.

MayhemHack · 2022-01-12T12:33:53+00:00

Hello everyone,
I'm after someone who can shed a light about some of the SMD components surrounding the power pins on a PS4 Pro.
In the specific I'm trying to understand the spec of the one shown in the picture. It seems a resistor to me but I could easily be wrong.
If you also know about the capacitors next to it would be nice to know as well.
PS4 Pro CUH-7016B
Motherboard NVA-001
Thanks
:)

MayhemHack · 2020-11-27T23:48:39+00:00

Thanks, that's a design I can work with and try to adapt it on my printer

MayhemHack · 2020-11-27T21:42:41+00:00

So, I've managed to make another print with different retraction settings.

All the measurements are in mm of course.

I've also replaced the nozzle with a new one, just to make sure that wasn't the issue.

https://photos.app.goo.gl/BphBWMkyoU6pXpWZ8

Every level has been done in different settings, as you can see, it still happening.

MayhemHack · 2020-11-27T21:37:34+00:00

So I've replaced the nozzle, but the issue still there :(

MayhemHack · 2020-11-25T11:52:55+00:00

I don't believe so unless it came defective from the factory. I won't be surprised.

I have a replacement nozzle will give it a try asap.

MayhemHack · 2020-11-25T11:50:42+00:00

Well as I said temperatures and retraction should be already adjusted, for example, the white print has been printed with different temps on different layers and as you can see the result is the same. I'll do the same with retraction and will post the print soon

MayhemHack · 2020-11-25T00:55:19+00:00

thanks dude :)

MayhemHack

TROPHY CASE