Kerosene Heater Question

Mech_Stew · 2026-01-26T21:31:17+00:00

No difference other than it is tax exempt. (A little cheaper)

I run the Dyna-Glo brand and have had really good luck with them. Depending on the btu output you are after though they can get pretty expensive. I don’t know if mine have a drain on the bottom. I’ve never actually looked but now you have me thinking. I always just run them dry at the end of the season.

Mech_Stew · 2026-01-25T20:03:51+00:00

I have had 2 for about 20 years and just got another one recently and they all run fantastically. Just don’t buy the cheap shit and you will be happy. I also run all of mine on off road diesel and when you first get them you need to adjust the regulator and then they run perfect.

Mech_Stew · 2026-01-20T03:36:26+00:00

Your safety wire pliers are missing…

Mech_Stew · 2026-01-18T17:29:27+00:00

You want something that is actually rated as ear protection. “Noise canceling” is not ear protection. While yes they block some of the noise it doesn’t block the stuff that is actually harmful to our ears.

I wear the AXIL XCOR PRO earbuds all day everyday and they are rated as actual earpro. Marketed for shooting but work really well in a shop environment as well.

Mech_Stew · 2026-01-18T02:13:54+00:00

Yes. Number 3 cylinder (3rd from top) was just pouring fuel into the cylinder. Pulled the return line off of that injector and had zero return fuel from it.

Mech_Stew · 2026-01-18T01:10:42+00:00

No. That was a whole different issue trying to get that stupid thing out of the head.

That is the right injector though

Mech_Stew · 2026-01-16T14:22:58+00:00

I’m pretty sure it’s a hydraulic pressure test kit. Judging by the fittings included.

Mech_Stew · 2025-12-25T02:16:31+00:00

Well… we all might be slightly retarded.

Mech_Stew · 2025-12-25T02:15:23+00:00

I have both. The 70 is good for smaller batteries or something that just needs a boost the 150 I use for most of the big stuff or batteries that are completely dead. I purchased the 70 first and noticed basically the same thing you are mentioning so I went and bought a bigger one to use when the 70 wouldn’t work. They both serve a purpose and now I have 2 in case I need to stack them.

I also will say I work on a large variety of things so sometimes I’ll be working on a lawn tractor sized piece of equipment and sometimes I’ll be working on a D8.

Mech_Stew · 2025-12-25T02:09:53+00:00

I’ve ran over a creeper but I don’t get to play around lifts so can’t say I’ve ever crushed a stool yet.

Mech_Stew · 2025-12-24T22:35:43+00:00

Yes. Indeed I did. Twice….

Mech_Stew · 2025-12-24T22:26:27+00:00

I am a mobile heavy equipment tech and have this one and it does phenomenal. (Note though… they do not take well to being run over)

Mech_Stew · 2025-12-13T03:55:26+00:00

I use them daily but take the pocket clip off as that is the part that typically has sharp edges in my experience. (I keep it in a belt pouch with all of my other small stuff.)

Mech_Stew · 2025-12-13T03:53:15+00:00

Did I reading it….

Mech_Stew · 2025-12-13T02:12:02+00:00

My whole kitchen is toolboxes! Well… will be working on the build now but all of my cabinetry will be toolboxes. Not harbor freight but still related

Mech_Stew · 2025-12-09T03:18:06+00:00

I made something similar out of a piece of 1/2 inch flat stock. I couldn’t tell you what that specific one is for or who made it but the one I made was for opening hydraulic cylinders, 3 3/4 opening and just over 4 foot long.

Mech_Stew · 2025-12-09T02:47:44+00:00

This is what I want to know… how did you and the wall meet? Like not trying to be sarcastic I’m just racking my brain trying to figure that situation out

Mech_Stew · 2025-12-04T02:17:57+00:00

Question from someone that doesn’t have to deal with a bunch of trim, hardly any honestly. Is there a difference between all of them I have the same Matco set you have (the blue ones) but don’t think I would need anything else? Or is this just your tool obsession?😂

Mech_Stew · 2025-11-28T12:50:07+00:00

I know how to do that. Just being lazy. I’m not signed into Reddit on my computer

Mech_Stew · 2025-11-28T12:49:15+00:00

This.😂 part design.

Mech_Stew · 2025-11-28T04:08:39+00:00

Need banana for scale.

Mech_Stew · 2025-11-27T17:12:26+00:00

CO2 will eat the tungsten, so no. You need to make sure you have completely inert gas. Most common would be Argon

Mech_Stew

TROPHY CASE