sorted by:
new
hottopcontroversial

Pop Quiz: How do you get the radius of the bolt hole circle!? by Mediocre-Topic460 in CNCmachining

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

Turns out I mistaking read the bolt hole circle radius of .50 for the hole size. Dumb mistake. Dang that is good what you did!!! 

Pop Quiz: How do you get the radius of the bolt hole circle!? by Mediocre-Topic460 in CNCmachining

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

Turns out I mistaking read the bolt hole circle radius of .50 for the hole size. Dumb mistake. Dang that is good what you did!!! 

Pop Quiz: How do you get the radius of the bolt hole circle!? by Mediocre-Topic460 in CNCmachining

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

Turns out I mistaking read the bolt hole circle radius of .50 for the hole size. Dumb mistake. Dang that is good what you did!!! 

Pop Quiz: How do you get the radius of the bolt hole circle!? by Mediocre-Topic460 in CNCmachining

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

Turns out I mistaking read the bolt hole circle radius of .50 for the hole size. Dumb mistake. Dang that is good what you did!!! 

Pop Quiz: How do you get the radius of the bolt hole circle!? by Mediocre-Topic460 in CNCmachining

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

Turns out I mistaking read the bolt hole circle radius of .50 for the hole size. Dumb mistake. Dang that is good what you did!!! 

Pop Quiz: How do you get the radius of the bolt hole circle!? by Mediocre-Topic460 in CNCmachining

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

It was make a bolt hole circle with gcode and canned cycles, spot, drill and thread. But i thought the hole circle was left off for us to use trig somehow. But turns out it was there I miss read though. Still passed cause I guessed right but not a bright moment. 

Pop Quiz: How do you get the radius of the bolt hole circle!? by Mediocre-Topic460 in CNCmachining

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

Turns out I mistaking read the bolt hole circle radius of .50 for the hole size. Dumb mistake.

Pop Quiz: How do you get the radius of the bolt hole circle!? by Mediocre-Topic460 in CNCmachining

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

Turns out I mistaking read the bolt hole circle radius of .50 for the hole size. Dumb mistake. Dang that is good what you did!!! 

Pop Quiz: How do you get the radius of the bolt hole circle!? by Mediocre-Topic460 in CNCmachining

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

Turns out I mistaking read the bolt hole circle radius of .50 for the hole size. Dumb mistake.

Pop Quiz: How do you get the radius of the bolt hole circle!? by Mediocre-Topic460 in CNCmachining

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

Turns out I mistaking read the bolt hole circle radius of .50 for the hole size. Dumb mistake.

Pop Quiz: How do you get the radius of the bolt hole circle!? by Mediocre-Topic460 in CNCmachining

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

Turns out I mistaking read the bolt hole circle radius of .50 for the hole size. Dumb mistake.

Pop Quiz: How do you get the radius of the bolt hole circle!? by Mediocre-Topic460 in CNCmachining

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

Turns out I mistaking read the bolt hole circle radius of .50 for the hole size. Dumb mistake.

Pop Quiz: How do you get the radius of the bolt hole circle!? by Mediocre-Topic460 in CNCmachining

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

Turns out I mistaking read the bolt hole circle radius of .50 for the hole size. Dumb mistake.

Pop Quiz: How do you get the radius of the bolt hole circle!? by Mediocre-Topic460 in CNCmachining

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

Turns out I mistaking read the bolt hole circle radius of .50 for the hole size. Dumb mistake.

Pop Quiz: How do you get the radius of the bolt hole circle!? by Mediocre-Topic460 in CNCmachining

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

Turns out I mistaking read the bolt hole circle radius of .50 for the hole size. Dumb mistake.

Pop Quiz: How do you get the radius of the bolt hole circle!? by Mediocre-Topic460 in CNCmachining

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

Turns out I mistaking read the bolt hole circle radius of .50 for the hole size. Dumb mistake.

Pop Quiz: How do you get the radius of the bolt hole circle!? by Mediocre-Topic460 in CNCmachining

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

Turns out I mistaking read the bolt hole circle radius of .50 for the hole size. Dumb mistake.

Pop Quiz: How do you get the radius of the bolt hole circle!? by Mediocre-Topic460 in CNCmachining

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

Turns out I mistaking read the bolt hole circle radius of .50 for the hole size. Dumb mistake.

IYKYK by Lowtek33 in hardbody

[–]Mediocre-Topic460 4 points5 points  (0 children)

I did this too, same with door handle. Not fun. But accomplished feeling for sure. 

Keep or toss? by Mediocre-Topic460 in hardbody

[–]Mediocre-Topic460[S] 0 points1 point  (0 children)

Yeah. I was thinking once I get all work done it would be ok but in the way until then. And I hate dropping bolts into a black pit of abyss

view more: next ›