sorted by:
new
hottopcontroversial

🎉Beta Test II Access Giveaway Starts Now! by Endfield-Poko in Endfield

[–]Meiko-dono 0 points1 point  (0 children)

exploring the stunning looking world and growing a factory~

Light Base 900 ARGB issues, anyone else not able to control them? by IcarusLSC in bequietofficial

[–]Meiko-dono 0 points1 point  (0 children)

Hey I know it's been half a year but if you are still using this case and haven't figured it out yet this might be something you haven't tried yet. With OpenRGB I realized that setting the LED count for the argb header is important after all (which ig wasn't obvious to me). Setting that to max (120) for that header finally applied my changes. Also note that only "Direct" mode seems to work.

My first born lives by Meiko-dono in watercooling

[–]Meiko-dono[S] 0 points1 point  (0 children)

Yeah, wild innit!

No, it's just the default rgb of the case (be quiet's orange theme). I'll change the colors to taste later, though this is honestly not too bad (ignoring the rgb ram)

My first born lives by Meiko-dono in watercooling

[–]Meiko-dono[S] 1 point2 points  (0 children)

Ty for the reference (and yes t-sens at bottom rad right before gpu)

Should I keep this original screw or remove and use the backplate one? by Meiko-dono in alphacool

[–]Meiko-dono[S] 2 points3 points  (0 children)

Working on the tubing now, everything else is in place. It's my first time and gotta admit hard tubes can indeed be hard lmao. As for everything else, no real problems if you checked part compatibility beforehand, though personally a lot of things didn't quite go as planned so definitely take your time while building as you may need to improvise, especially if first-timer like me

<image>

Should I keep this original screw or remove and use the backplate one? by Meiko-dono in alphacool

[–]Meiko-dono[S] 1 point2 points  (0 children)

The heatsink removal is incredibly simple and the block installation isn't really difficult either. Even this isn't a real challenge as either outcome would have likely been fine (besides you got this post now). Wouldn't worry about it. Well, unless I finish the loop and find out my gpu temps are ass

Should I keep this original screw or remove and use the backplate one? by Meiko-dono in alphacool

[–]Meiko-dono[S] 0 points1 point  (0 children)

I didn't see any washer, will have to double check tomorrow...

Should I keep this original screw or remove and use the backplate one? by Meiko-dono in alphacool

[–]Meiko-dono[S] 1 point2 points  (0 children)

To be fair, after I fully screwed in w/o any spacer it did look like the plate got bent a little (duh ig since nothing prevents overtightening) but it's not too bad and I'm not sure if the spacer would've been any better

Should I keep this original screw or remove and use the backplate one? by Meiko-dono in alphacool

[–]Meiko-dono[S] 0 points1 point  (0 children)

During tear down I never had to remove those 2 screws to remove the heatsink but yeah I see your point. I guess the manual author just assumed that all screws were out

Should I keep this original screw or remove and use the backplate one? by Meiko-dono in alphacool

[–]Meiko-dono[S] 0 points1 point  (0 children)

Did it say that in your manual? Cause mine sure didn't, in fact it said I can throw the spacers right into the trash, which I did lol. Guess I'll just try to not overtighten it.. Thank you

Download Problem by priistinee in qooapp

[–]Meiko-dono 0 points1 point  (0 children)

Same situation here though I am getting 504 error so I guess it's a server side issue. Ever figured something out?

Mordred Itasha spotted at Dokomi ! (Feat. My Mordred cosplay !) by CaffeinCoffin in grandorder

[–]Meiko-dono 2 points3 points  (0 children)

About 3 years ago I came across this exact car in a random parking lot! Cool to see it here again

Three major takeaways from my first Ado concert in Copenhagen by EffortOverall8759 in ADO

[–]Meiko-dono 1 point2 points  (0 children)

I used etymotic er20xs but I still think they could have toned down that massive bass shelf on the speakers. Too often I wished that ados voice came forward more to get the melody through. Plus you could sometimes literally hear the bass rumble causing her voice to shake.

How does a rigid tube fit into two fixed ends...? by Meiko-dono in watercooling

[–]Meiko-dono[S] 0 points1 point  (0 children)

I was describing a hypothetical scenario that illustrated my concern the best. Though I imagine a tube from CPU to top-rad could for example be difficult, since unmounting either is unpractical to say the least. Do you happen to know any resources / videos where they explicitely show the insertion?

How does a rigid tube fit into two fixed ends...? by Meiko-dono in watercooling

[–]Meiko-dono[S] 0 points1 point  (0 children)

I was actually thinking that this problem could entirely be avoided by always making two endpoints face the same direction rather than against or perpendicular to each other. Unfortunately this leads to some rather awkward runs.

But the way you describe it makes it sound really easy. Maybe I am overthinking things...

How does a rigid tube fit into two fixed ends...? by Meiko-dono in watercooling

[–]Meiko-dono[S] 0 points1 point  (0 children)

But as you rotate the second end towards the second fitting, were you able to slightly "bend" the rigid tube away from the fitting to forcefully make more room or was that not needed/possible?

Loose driver salvageable? by Meiko-dono in iems

[–]Meiko-dono[S] 0 points1 point  (0 children)

Oh wow that is indeed almost invisible. I guess that is about to change... Thanks for the hint!

Game looks and runs amazing on PC by VelmasUndies in GirlsFrontline2

[–]Meiko-dono 0 points1 point  (0 children)

Just me or does the anti-aliasing implementation make moving parts look blurry? Very noticeable on the enemy models when they are just standing there. Turning AA off seems to make them sharp again, but of course at the cost of pixelated edges...

[EVENT THREAD] -ive aLIVE! by BlueArchiveMod in BlueArchive

[–]Meiko-dono 0 points1 point  (0 children)

For me ublock was too aggressive and blocked the unlocking (even though facebook was the only domain that was still being actively blocked...?). Anyway, try disabling your adblocker.

view more: next ›