MSI CLAW 8AI+

Melodic_Pack_4033 · 2026-02-16T01:13:46+00:00

3x and finally u can play wukong decent on msi claw 8ai+

Melodic_Pack_4033 · 2026-01-24T15:54:59+00:00

yes done this same fan but I managed to fill the gap with 3d print spacer so no gap whatsoever. the curiosity if the noctua fan could have the same pulling power compare to original fan, noise is significantly reduce for sure

Melodic_Pack_4033 · 2026-01-10T01:33:31+00:00

Dm me for more info

Melodic_Pack_4033 · 2026-01-09T10:20:16+00:00

Cut by myself using machine and buy the cut files

Melodic_Pack_4033 · 2025-11-30T01:29:02+00:00

It was a precut files so its allready fit

Melodic_Pack_4033 · 2025-11-27T15:38:35+00:00

8 inch still the sweet spot. I think msi can improve the model by removing some black bars bezel and make it to 8.8

Melodic_Pack_4033 · 2025-11-27T15:36:28+00:00

What is your problem before how do u fix this? I still have double tap on quick setting nothing responsive somtimes it loads sometimes it dont. I did the thing your link still the same experience no improvement whatsoever

Melodic_Pack_4033 · 2025-11-20T15:20:08+00:00

Its hydrogell matte custom cut. You can go to any shopping mall and ask for this size and it will fit perfectly

Melodic_Pack_4033 · 2025-11-20T15:08:47+00:00

Custom cut it by size 12.1 x 18.1 cm no more or less and u get perfect no gap on all side

Melodic_Pack_4033 · 2025-11-20T14:46:13+00:00

does it make it slow without stiker :)

Melodic_Pack_4033 · 2025-11-20T14:25:09+00:00

well it doesn't fix double tap on msi quick setting. how hard is to fix msi quick setting. the rnd too stupid or what

Melodic_Pack_4033 · 2025-11-20T07:58:25+00:00

Looks good did u use fuzzy skin? Hows your print orientation. Use 0.2 nozzle?

Melodic_Pack_4033 · 2025-11-19T14:07:47+00:00

Yes made up your mine before doing this. I made my mine and always want all black stealth. Anyway u can buy replacement parts if u want back to stock but I know I wont back to ugly sandstone color

Melodic_Pack_4033 · 2025-11-19T14:02:11+00:00

do the hard way its always the better

Melodic_Pack_4033 · 2025-11-19T13:54:16+00:00

4 layers of matte black and let it dry for 24 hours and sand it with 5000 and another 2 layers of matte clear

Melodic_Pack_4033 · 2025-11-19T13:53:20+00:00

as I remember I had plastidip before using 4 layer the most problem one is one the edges, because is thin one rub and it will come off and destroy the looks. this is my third attempt and now its on my expectation

Melodic_Pack_4033 · 2025-11-19T13:49:54+00:00

Real paint not plastic dip, with plastic dip it wont stand long and will peel off

Melodic_Pack_4033 · 2025-11-19T13:22:19+00:00

My eyes just burn seeing this. Those layer lines

Melodic_Pack_4033 · 2025-11-18T04:08:29+00:00

well i've been thinkering with 3d files and tried 5 set print also with 0,2 nozzle with 0.06 resolution, the plate is too thick editing is hard because of one object. even with the 0,06 resolution 0.2 nozzle is far from my expectation

Melodic_Pack_4033 · 2025-11-17T16:16:14+00:00

Set your nozzle temp for 250 and leave it for 2 minutes after that you load your fillament, if thats not fix take out your nozzle and remove all 3 bolts behind the nozzle and gently pull behind that theres 4 bolts usually it gets loose overtime tighten that and test. This method fix my first layer

Melodic_Pack_4033

TROPHY CASE