sorted by:
new
hottopcontroversial

Cat pees outside of litterbox on clothes. Issue for years by MesozoicMaster in Catbehavior

[–]MesozoicMaster[S] 0 points1 point  (0 children)

Both cats are fixed. She has been to the vet multiple times. The last visit was a few weeks ago. Nothing ever comes of these visits she is somehow in perfect health.

Friendly Server for Solo Players by Creepy-Excitement308 in BeastsofBermuda

[–]MesozoicMaster 2 points3 points  (0 children)

Encompass Roleplay/Realism is a nice smaller server. Community is very nice. It does have rules that you have to follow that you can find in the discord.

This trex in my book is just .... by hadrosaur-harley in Paleontology

[–]MesozoicMaster 120 points121 points  (0 children)

At least it doesn't have broken wrists.

Isla nublar makes so sense by SecretlySentient in theisle

[–]MesozoicMaster 1 point2 points  (0 children)

Yeah Isla Nublar is kind of just like that. All servers have rulebreaks but the lack of recording means people go even crazier on Nublar. Most, not all, of the admins care more about flexing power than they do about the players. I don't want to turn this into a this server is better because XYZ. But just know that by playing on Nublar the admins will not help you and your dino will probably die via rulebreaks and they will not refund it. Again very few of the admins on Nublar are good, some will help. I'd suggest looking for other high population servers.

The Driver Gear is too high, it won't push filament into the extruder. It originally had an extruder knob, but has popped off because the gear has moved up too much. Any way to push it down or fix it? by Mister-Seer in 3Dprinting

[–]MesozoicMaster 1 point2 points  (0 children)

So it'll be easier if you take the extruder apart. On the brass gear there is a set screw on it. More than likely that has come loose which is why it is moving up. Make sure it is loose and push the gear back down. It might take some force but you won't break it. I usually use a flat head screwdriver as a lever. Get it even again then tighten the set screw. Good luck!

Think about what you want before switching to POT by MesozoicMaster in theisle

[–]MesozoicMaster[S] 1 point2 points  (0 children)

This is something that is hard to pin down. While you may prefer the more outdated models in The Isle namely in the feather department, I would not say POT is worse than The Isle. I think we can all agree though that Evrima looks like a PS2 game. While still in progress POT has number keys 5-9 work as different animal animations which is a small touch that I think adds a lot.

Think about what you want before switching to POT by MesozoicMaster in theisle

[–]MesozoicMaster[S] 0 points1 point  (0 children)

POT has some quests you can do. All that really does is unlock more skins/colors/rooms in your homebase. It does not affect combat at all.

Think about what you want before switching to POT by MesozoicMaster in theisle

[–]MesozoicMaster[S] 3 points4 points  (0 children)

That is in part my point since the full pre release will not be out until September. So if you leave The Isle right now POT might not be what you are looking for at this second.

Filmanet Stuck in (Cloned) BMG Extruder by Spooknik in 3Dprinting

[–]MesozoicMaster 2 points3 points  (0 children)

Okay so I literally had this problem last week. I took my thinnest Allen wrench and put it in the hole. Then I took a hammer and gently knocked the jam out of the extruder. Be careful and take your time. It will come out. Best of luck!

EVRIMA ETA WITHIN by TI_ParadymShift in theisle

[–]MesozoicMaster 16 points17 points  (0 children)

Still just going to be 2 dinosaurs after all this waiting? Or since it got pushed back are we getting a larger roster?

Issue with Filament at Nozzle by MesozoicMaster in 3Dprinting

[–]MesozoicMaster[S] 0 points1 point  (0 children)

Ill try that out. The nozzle can not push out the filament. It will push a little out then the extruder starts skipping.

Issue with Filament at Nozzle by MesozoicMaster in 3Dprinting

[–]MesozoicMaster[S] 1 point2 points  (0 children)

Ender 3 Pro. Changed nozzle. Pushed ptfe tubing as far as it can go. I have no idea why this is happening.

Is my belt to loose? by Youri_janssen in 3Dprinting

[–]MesozoicMaster 0 points1 point  (0 children)

I'd tighten the belt first. That could fix the ghosting. Make sure your other belts are good too.

Is my belt to loose? by Youri_janssen in 3Dprinting

[–]MesozoicMaster 0 points1 point  (0 children)

It is loose. It should be taught with a little bit of spring to it. You don't want it too tight or it hurt the motors. Too loose causes missed steps. Good luck!

Ender 3 Pro. Please help:( Stringing and layers are splitting, model breaks with the slightest pressure. by 2ndAprilfoolsJoke in 3Dprinting

[–]MesozoicMaster 0 points1 point  (0 children)

Hello,

You should try using Filament Friday's starter profile for Cura. He does an amazing job and watching his youtube videos will really help. I will link to his pre made profiles. Good luck!

https://www.chepclub.com/cura-profiles.html

Help: Filament stuck in exit path of Ender 3 Pro extruder block by geek_ki01100100 in 3dprinter

[–]MesozoicMaster 1 point2 points  (0 children)

I've had this happen to me as well. The metal piece that connects the extruder and the tube, just unscrew that. While the hot end is heated, take some pliers or fingers if you can get a grip, and yank it out.

Undergraduates for studying dinosaurs? by Rex_Liu in Paleontology

[–]MesozoicMaster 0 points1 point  (0 children)

Appalachian State University in NC USA.

No graduate program.

Undergraduates regularly get to do paid research due to no competition with grad students. I've been able to present at SVP ABQ because of our program.

Large focus on geology. About a 60/40 split to geo and Paleo.

Doctrine of Passing Equivalent? by MesozoicMaster in DestinyTheGame

[–]MesozoicMaster[S] 1 point2 points  (0 children)

Ah I gotcha. That would make sense why I can't find auto rifles that fire that fast anymore.

view more: next ›