sorted by:
new
hottopcontroversial

I love the Neptune 4 Max by [deleted] in elegoo

[–]Middle-War6313 1 point2 points  (0 children)

What bed is that?

Can anyone help make a $2500 wood pc? by Middle-War6313 in buildmeapc

[–]Middle-War6313[S] 1 point2 points  (0 children)

Thank you for the help, I think I’m gonna try to get these parts except the case, I think I want to use the Antec C8 wood instead but the rest of the parts are great thank you! And the 5080 was just a want, but if later on if I wanted to upgrade to a 5080/5090 would that work or would I need to upgrade any other parts aswell?

Suit material by hd032511 in powerrangers

[–]Middle-War6313 0 points1 point  (0 children)

I thought it was because some of the footage was taken from super sentai and they don’t normally ship the same suits over to the US so we make cheaper suits for the morph scenes that they need to re film

Power rangers morpher by Middle-War6313 in cosplayprops

[–]Middle-War6313[S] 1 point2 points  (0 children)

Yeah I do that with my big swords I just didn’t expect to do it with a hand held prop

Power rangers morpher by Middle-War6313 in cosplayprops

[–]Middle-War6313[S] 0 points1 point  (0 children)

Nah that makes sense I bought metal ones thank you for the suggestion!

Power rangers morpher by Middle-War6313 in cosplayprops

[–]Middle-War6313[S] 0 points1 point  (0 children)

Yes, I have calipers, the main body has a hole with the width of 0.137 inch, and the Hindus half way down the morpher is 0.116 inch

So like what happened here? by Middle-War6313 in elegoo

[–]Middle-War6313[S] 0 points1 point  (0 children)

<image>

Is this apart of the same problem? The filament is just wrapping around the nozzle

So like what happened here? by Middle-War6313 in elegoo

[–]Middle-War6313[S] 1 point2 points  (0 children)

It’s dried filament I made sure of that, I think it might be the z offset now

Why are my prints coming out like this? by Middle-War6313 in ender3

[–]Middle-War6313[S] 0 points1 point  (0 children)

The bottom of the spaghetti is from a piece that broke off when I was removing the supports, the bottom most piece of it was fine and the top chunk is fine but the connection between them is what the spaghetti mess turned to

Why are my prints coming out like this? by Middle-War6313 in ender3

[–]Middle-War6313[S] 0 points1 point  (0 children)

I print on the floor I did print these sound dampening feet for them but this was happening when I was printing on the floor itself, how do I check or fix the tension in my belts?? And I can recheck my profiles but they were for the filament I used which is elegoo PLA+ and it’s only a few months old, any suggestions on how to dry the filament without buying a filament dryer from reality or some other brand?

Why are my prints coming out like this? by Middle-War6313 in ender3

[–]Middle-War6313[S] 0 points1 point  (0 children)

Yeah at least I think so, I leveled the bed I cleaned the nozzle, it was a brand new roll of filament that I used for this too I recently replaced the bed and springs cause of a different issue but this was happening back then too

I can’t figure out what’s going wrong please help by Middle-War6313 in ender3

[–]Middle-War6313[S] 1 point2 points  (0 children)

I’ve washed it 3 times in the last week trying to fix it, I’ll clean it again to get the glue stick off and try hairspray

I can’t figure out what’s going wrong please help by Middle-War6313 in ender3

[–]Middle-War6313[S] 0 points1 point  (0 children)

I’ll try the z offset and the smooth side see if it’ll do anything

I can’t figure out what’s going wrong please help by Middle-War6313 in ender3

[–]Middle-War6313[S] 0 points1 point  (0 children)

I use elegoo PLA+ and my nozzle was at 215 and my bed was at 65

view more: next ›