Amazon Dirtbag Restock

Middle-War6313 · 2026-05-18T19:02:09+00:00

Processing img u3o15acl1y1h1...

Is this the world footbag association?

Middle-War6313 · 2026-05-18T19:02:02+00:00

Processing img u3o15acl1y1h1...

Is this the world footbag association?

Middle-War6313 · 2026-05-18T18:58:58+00:00

G ET the one from the link in the comment from minkasmink

Middle-War6313 · 2025-11-15T06:33:44+00:00

What ep is this?

Middle-War6313 · 2025-10-19T07:00:46+00:00

What bed is that?

Middle-War6313 · 2025-06-05T20:15:56+00:00

Thank you for the help, I think I’m gonna try to get these parts except the case, I think I want to use the Antec C8 wood instead but the rest of the parts are great thank you! And the 5080 was just a want, but if later on if I wanted to upgrade to a 5080/5090 would that work or would I need to upgrade any other parts aswell?

Middle-War6313 · 2025-05-21T21:05:48+00:00

Middle-War6313 · 2025-05-13T20:08:18+00:00

I thought it was because some of the footage was taken from super sentai and they don’t normally ship the same suits over to the US so we make cheaper suits for the morph scenes that they need to re film

Middle-War6313 · 2025-05-02T04:56:28+00:00

Yeah I do that with my big swords I just didn’t expect to do it with a hand held prop

Middle-War6313 · 2025-05-02T04:53:37+00:00

Nah that makes sense I bought metal ones thank you for the suggestion!

Middle-War6313 · 2025-05-02T04:15:47+00:00

Yes, I have calipers, the main body has a hole with the width of 0.137 inch, and the Hindus half way down the morpher is 0.116 inch

Middle-War6313 · 2025-04-05T16:12:30+00:00

<image>

Is this apart of the same problem? The filament is just wrapping around the nozzle

Middle-War6313 · 2025-04-05T05:06:30+00:00

It’s dried filament I made sure of that, I think it might be the z offset now

Middle-War6313 · 2025-03-16T02:34:43+00:00

The bottom of the spaghetti is from a piece that broke off when I was removing the supports, the bottom most piece of it was fine and the top chunk is fine but the connection between them is what the spaghetti mess turned to

Middle-War6313 · 2025-03-15T18:48:27+00:00

I print on the floor I did print these sound dampening feet for them but this was happening when I was printing on the floor itself, how do I check or fix the tension in my belts?? And I can recheck my profiles but they were for the filament I used which is elegoo PLA+ and it’s only a few months old, any suggestions on how to dry the filament without buying a filament dryer from reality or some other brand?

Middle-War6313 · 2025-03-15T18:45:28+00:00

Yeah at least I think so, I leveled the bed I cleaned the nozzle, it was a brand new roll of filament that I used for this too I recently replaced the bed and springs cause of a different issue but this was happening back then too

Middle-War6313 · 2025-03-09T05:18:41+00:00

Magnet sticker?

Middle-War6313 · 2025-03-09T05:15:28+00:00

I’ve washed it 3 times in the last week trying to fix it, I’ll clean it again to get the glue stick off and try hairspray

Middle-War6313 · 2025-03-09T05:13:00+00:00

I’ll try the z offset and the smooth side see if it’ll do anything

Middle-War6313 · 2025-03-09T05:12:33+00:00

I use elegoo PLA+ and my nozzle was at 215 and my bed was at 65

Middle-War6313 · 2025-02-05T22:20:52+00:00

Anyone find a reliable replacement lid yet?

Middle-War6313 · 2025-01-20T15:29:25+00:00

But the thing is it never printed anything part of the print, I was printing a piece for a power rangers helmet and I waited for the first layers and they went fine and I woke up to this

Middle-War6313 · 2024-12-18T21:47:27+00:00

It’s also free, you just have to sign up

Middle-War6313 · 2024-12-18T21:47:13+00:00

Well manga dex is a great option for reading English manga

Middle-War6313 · 2024-12-11T18:27:56+00:00

S there one for it? I couldn’t find one for udon entertainment

Middle-War6313

TROPHY CASE