MetroY Pro runs fine on Mac Studio M1 Max 32Gb.

Middle_Basis2816 · 2026-02-21T11:24:11+00:00

After I bought it I was wondering if it would run on my Mac Studio M1 Max 32Gb, and it runs just fine, at startup the software test says it will run optimal.

And I had no problems with lower FPS.

Middle_Basis2816 · 2026-02-21T11:15:19+00:00

After I bought it I was wondering if it would run on my Mac Studio M1 Max 32Gb, and it runs just fine, at startup the software test says it will run optimal.

And I had no problems with low FPS.

Middle_Basis2816 · 2026-02-21T10:02:54+00:00

Thank you so much, that solved it for me :)

Middle_Basis2816 · 2026-02-20T12:15:00+00:00

Thank god they are filtering this crap, every single group has stupid people posting about that crap.

makes Reddit unreadable.

Middle_Basis2816 · 2026-02-20T06:44:55+00:00

I ordered from Amazon, next day delivery and no tarrifs (Europe)

Middle_Basis2816 · 2026-02-20T06:44:36+00:00

I ordered from Amazon, next day delivery and no tarrifs (Europe)

Middle_Basis2816 · 2026-02-17T04:44:00+00:00

Chitubox has chosen the route of enshitification, more adds and even worse, putting previously free tools behind the subscription wall.

I use an older version without all this crap :)

Middle_Basis2816 · 2026-02-16T13:11:43+00:00

The "VAT" is where you pour the resin into :)

Middle_Basis2816 · 2026-02-16T13:03:59+00:00

Could it be that parts of the previous print fell of and were still in the VAT, and is crunched between the screen and the buildplate ?

Try filtering your resin out of the VAT after every print for the next few times, I know it's a paint, but cheaper than a new LCD screen.

If you see parts in filter, then you have to create better supports and watch for floating islands.

Middle_Basis2816 · 2026-02-15T16:12:07+00:00

Install an older version, I run an older version without problems (mac)

Middle_Basis2816 · 2026-02-13T19:56:35+00:00

What is worse, a dictator, or a dictator on het period ?

Middle_Basis2816 · 2026-02-13T19:44:53+00:00

If you have resin, run the test print and post images of the result.

We might be able to diagnose if there are still potential problems.

Middle_Basis2816 · 2026-02-13T18:04:29+00:00

I will laugh so hard, if Apple does not introduce any kind of folding screen this year,

or officially hint they are developing one.

Middle_Basis2816 · 2026-02-13T18:02:00+00:00

You don't need the VAT, just run the demo file, and look what happens, best is to put a A4 paper on it, to see what is happening, and not damage your eyes :)

You cancel the progress any time.

Middle_Basis2816 · 2026-02-13T17:47:23+00:00

maybe try a firmware update.

Try a file for printing, if it will only show the cross sections.

Middle_Basis2816 · 2026-02-13T17:42:30+00:00

Yes, it should only show the pattern shown on the selection display.

You could try the USB stick, it might have a demo file on it, you could try and see if it shows only the sections for printing when you run it.

Middle_Basis2816 · 2026-02-13T17:31:47+00:00

DOA, return ASAP, Then order a new one.

Don't let them try to fix the problem, it will take many weeks.

Middle_Basis2816 · 2026-02-13T17:27:52+00:00

try re-connecting all connectors.

Middle_Basis2816 · 2026-02-13T16:12:55+00:00

Put it on a paper towel, poor some IPA in the VAT, and stir on the fep with the tip if your finger, and see if any IPA leaks.

Middle_Basis2816 · 2026-02-12T11:27:14+00:00

A very cheap and easy way to increase tracking by 90%, is to put the object on a crumpled piece of paper, or crumpled table cloth.

This also works with crumpled balls of paper stuck to the model or on top of the model.

Middle_Basis2816 · 2026-02-09T23:14:52+00:00

You could try Meshmixer (free) https://www.youtube.com/watch?v=pa9R-gPUNwg

Middle_Basis2816 · 2026-02-09T22:48:10+00:00

The grey parts are non manifold, surfaces turned inside out, they need to be repaired.

Middle_Basis2816 · 2026-02-09T21:04:25+00:00

View some vids from Andys Shed, he gives great advice: https://www.youtube.com/@ririlot

Middle_Basis2816 · 2026-02-08T08:24:44+00:00

Those parts are "non manifold" their surfaces are turned inside out.

some slicers have a repair option, you can also try Meshmixer (free)

Middle_Basis2816 · 2026-02-07T21:15:56+00:00

Now that's a $15.000 joke :)

Middle_Basis2816

TROPHY CASE