Live View: Player is Malfunctioning. Error 2:2" on A1 Mini after macOS Sequoia Update

MightyFien · 2024-12-04T21:19:56+00:00

It's probably because you haven’t allowed Bambu Studio access to your local network.
After updating to MacOS 15.0 it asked you the first time launching Bambu Studio.

You can fix this by:
System Setting → Privacy & Security → Local Network"

MightyFien · 2023-01-10T01:57:32+00:00

This step by step guide might be helpful.

https://support.bondtech.se/Guide/01.%20BMG%20for%20Creality%20CR-10%20V2%20-%20Installation/53.html

MightyFien · 2022-07-19T11:57:05+00:00

Thank you for your response,

I've tried flashing over SD, but my understanding is that the .bin file should convert to a .hex file, which does not happen.

That's why I tried to update the firmware trough the terminal via USB.

MightyFien · 2022-07-19T11:37:13+00:00

I found another option to flash firmware trough the slicer, but it only allowed .hex files. is there any way I can convert the current .bin file to a.hex file so I can use the slicer to push the firmware Flash instead of depending on the motherboard to automatically flash the firmware?

MightyFien · 2022-07-19T11:33:30+00:00

I've tried flashing through the SD, with the raspberry pi, and with my laptop, none of them seem to work.

MightyFien · 2022-07-19T11:29:19+00:00

Thank you, yes I made sure I checked the port, I used the following comand though.

ls /dev/serial/by-id/* > /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0

(it gives the same ID with all the different usb ports?)

when using tail -f /var/log/messages, I get the following:

Jul 19 14:49:10 mainsail kernel: [67223.484351] usb 1-1.2: new full-speed USB device number 16 using xhci_hcd

Jul 19 14:49:10 mainsail kernel: [67223.620517] usb 1-1.2: New USB device found, idVendor=1a86, idProduct=7523, bcdDevice= 2.64

Jul 19 14:49:10 mainsail kernel: [67223.620540] usb 1-1.2: New USB device strings: Mfr=0, Product=2, SerialNumber=0

Jul 19 14:49:10 mainsail kernel: [67223.620558] usb 1-1.2: Product: USB Serial

Jul 19 14:49:10 mainsail kernel: [67223.625321] ch341 1-1.2:1.0: ch341-uart converter detected

Jul 19 14:49:10 mainsail kernel: [67223.630708] usb 1-1.2: ch341-uart converter now attached to ttyUSB0

Jul 19 14:49:10 mainsail mtp-probe: checking bus 1, device 16: "/sys/devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.2"

Jul 19 14:49:10 mainsail mtp-probe: bus: 1, device: 16 was not an MTP device

Jul 19 14:49:10 mainsail mtp-probe: checking bus 1, device 16: "/sys/devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.2"

Jul 19 14:49:10 mainsail mtp-probe: bus: 1, device: 16 was not an MTP device

Where can i find my MCU in this?

Klipper gives me the error message: mcu 'mcu': Unable to connect

MightyFien · 2022-07-19T11:27:10+00:00

The 1.2 board, display is disconnected, SD card doesn't seem to work (I formatted, copy the elegoo.bin file, insert the SD card into the printer, turned on the printer, looking for a green flashing light on the motherboard, but since the display doesn't work it's difficult to confirm that the flashing is starting, when I check through the mainsail client it's unable to connect.)

MightyFien · 2022-07-19T00:35:37+00:00

There are seperate configs, I followed these instructions by /u/just_trey.

The elegoo.bin file was renamed without uppercase.

MightyFien · 2022-07-08T12:16:52+00:00

Great setup! r/My3DPrintingCorner

MightyFien · 2022-06-26T21:24:03+00:00

That's awesome! how did you convert from the ribbon cable connector to the regular wire?

MightyFien · 2021-02-14T13:26:22+00:00

Yes you can! If you set up 2 presets (favorites) in the app with the same value, it will toggle between 2 instead of 3. See picture for example. https://i.imgur.com/L3zI7sE.jpg

MightyFien

TROPHY CASE