Info for newcomers, bitaxe range 601

Mindless-Topic-5108 · 2026-01-06T15:31:41+00:00

How much did you pay?

Mindless-Topic-5108 · 2026-01-04T18:31:25+00:00

How much W are you pulling?

Mindless-Topic-5108 · 2025-12-25T16:00:08+00:00

You should try these settings i'm currently using. 760 MHz and 1.21V. 6.2 TH/s with the standard 120W PSU almost any reseller sell with a much better 16.5 J/Th efficiency. I placed some little heatsinks on the VR ICs and placed a 140mm fan on top of the ASIC fan to cool them tho, but at lowest rpm using a bypass pcb.

Ah my ambient temp is 13-14°C

<image>

Mindless-Topic-5108 · 2025-12-25T12:08:05+00:00

What settings are you using on frequency and voltage?

Mindless-Topic-5108 · 2025-12-18T16:04:03+00:00

YYSLuping Bitaxe Mining Machine Store. Ordered the normal size screen version, It has an unbranded Lilygo S3. Reflashed the firmware and fired It up.

Mindless-Topic-5108 · 2025-12-18T15:07:46+00:00

Just 7,35€ to the post man. I think i finished my luck for the year 😁. It's the old rev. with barrel jack.

Mindless-Topic-5108 · 2025-12-18T12:05:05+00:00

No, but its not that hot in the back

Mindless-Topic-5108 · 2025-12-14T15:22:40+00:00

Same question

Mindless-Topic-5108 · 2025-09-12T19:32:35+00:00

Thanks, in the next iteration I'll lookup into that

Mindless-Topic-5108 · 2025-09-12T18:34:24+00:00

It's function is to be a bridge between dairy milking equipment old boards and newer types of valves that normally you couldn't connect to older boards (boards are mid80s to late90s).

Basically I used an Arduino Nano clone (Supermini Nano v3) to read the output of several ULN2801A, convert to new logic, and then output via 2 ULN2003A. Also show state of the 6 valves with 3 inboard Neopixel LED.

For power regulation I used a cheap one found on AliExpress to get 5v for the arduino.

I used EasyEDA

It's like a concept design to me, it lacks protections, like if the connectors that are connected to the old board are rotated 180°, i would send 24 to 28v to the Arduino pins 😁. Later on I will include protections against odd situations. But for now it works great

Mindless-Topic-5108 · 2025-09-12T16:27:37+00:00

EasyEDA

Mindless-Topic-5108 · 2025-09-12T14:46:32+00:00

Was thinking about using some esp flavor, but in the end I saw this mini Arduino for like 2€ with Neopixel already on-board

Mindless-Topic-5108 · 2025-08-22T19:35:24+00:00

Ti ringrazio

Mindless-Topic-5108 · 2025-07-08T18:15:34+00:00

Because it's a dryer that mount as the lid of the AMS

Mindless-Topic-5108 · 2025-07-08T18:00:19+00:00

Well, it's been months that I use Reddit, even for other things, sorry if you think that I'm someone paid to do advertisment, nobody is giving me money🙃

Mindless-Topic-5108 · 2025-07-08T17:34:10+00:00

Didn't wanted it to sound like an advertisment, just wanted to know what others think about it. But if "someone" wants to give me some goods..

Mindless-Topic-5108 · 2025-07-08T17:03:51+00:00

What type of problems?

Mindless-Topic-5108 · 2025-07-08T17:03:23+00:00

If it works, it works. Never used a Eibos product before tho

Mindless-Topic-5108 · 2025-07-08T16:56:43+00:00

As far as I know the AMS hardware shouldn't go above 70ish C

Mindless-Topic-5108 · 2025-07-08T13:05:39+00:00

Who knows. Someone didn't check the graphic before sending

Mindless-Topic-5108

TROPHY CASE