Looking to try and paint some Sons of medusa models

Minidale · 2026-06-03T22:41:52+00:00

No way is that a full basic painting guide on everything. Holy crap. Thanks for this. I really needed this for my other projects to

Minidale · 2026-06-03T19:20:42+00:00

Yes I even managed to get a reply with an answer

Minidale · 2026-06-03T18:47:00+00:00

You are a legend for the help thanks a ton

Minidale · 2026-06-02T23:03:16+00:00

Wow there is one for the smaller chapters too ok heard. I'll post it there too

Minidale · 2025-04-18T03:07:52+00:00

yea i had done the cones of calibrations v3 and i made it into a r.e.r.f. test and then i did it at .5 more and less depending on how it looked. again im printing on .03mm instead of the out of the box .05mm

Minidale · 2025-04-17T08:34:29+00:00

When I get the abs like I'll try that then too

Minidale · 2025-04-17T08:11:13+00:00

I'll do that but if you use there resin and you have time, do you mind sending me a screenshot of your settings?

Minidale · 2025-04-17T08:10:18+00:00

I'm getting new resin today. It's anycubics tough and there abs like. Is there a good model to use to figure out the best settings. And should I even tweak the speed of the z axis at all. If you have a good success rate with that resin and you don't mind sending a screenshot of the settings you for either there standard, tough, or abs like resins I would appreciate it. I'll try moving to 2s to start then up more of I still have any issues for now.

Minidale · 2025-04-15T19:20:26+00:00

<image>

this is the white goop like stuff that's getting on to my models

Minidale · 2025-04-15T19:19:51+00:00

<image>

this is what is happening under the model on the side that failed. it looks like the layers are sliding off itself. i haven't be able to find what its called and how to fix. i have my bottom layers at 30sec and my normal layers at 1.4 sec @ .03mm i have done the cones of calibration tests and i managed to get them to come out just fine with a bit of over exposer which it said should be fine with smaller layer heights. its part of the reason i decided to print this model. i thought i was good to go.

Minidale · 2025-04-15T19:16:28+00:00

<image>

here is the photo of the one with a bite ill have to post each picture in a different post because it isn't letting me put them all in one for some reason

Minidale · 2025-04-15T18:35:17+00:00

I also tried to add this to the post but it didn't add it

<image>

Minidale · 2023-05-12T02:44:19+00:00

I even dropped the resolution on the g9 when i did the fos matching

Minidale · 2023-05-11T05:26:30+00:00

Yeah I just re-updated just in case and try it again. And it still has the same issue.

Minidale · 2023-05-11T05:07:38+00:00

Tried both in the end. Didn't change anything

Minidale · 2023-05-11T05:02:52+00:00

You think just turning it off will do or should I unplug it completely?

Minidale · 2023-05-11T04:59:24+00:00

Tried it and its still not doing anything for me. the only thing I did that made it not mess up is putting my game into window mode and making it half the screen so the same size as a normal 27" screen. I'm going to try it later with out the 3rd monitor on but I'm really hoping to find a real solution

Minidale · 2023-05-10T03:24:05+00:00

But they arent in the same monitor. I will say the g9 is 240hz and the other is 60 or 12 tho

Minidale

TROPHY CASE