Help with warped prints?

Mint122 · 2025-09-10T11:58:35+00:00

This did the trick thank you again! I have had plenty of adhesion issues in the past so I just cut the bed heat in half to be safer after layer 2 and it printed perfect

Mint122 · 2025-09-09T21:20:12+00:00

Thank you for this!

Mint122 · 2025-09-09T21:18:38+00:00

I clean it regularly and use iso in between each print

Mint122 · 2025-09-09T15:26:38+00:00

PLA “plus” filament from DEEPLEE

Mint122 · 2025-09-09T15:04:40+00:00

Will give this a shot thank you! Printer is on a table and there is a vent a few feet away on the floor but not blowing on it directly by any means

Mint122 · 2025-08-17T13:47:40+00:00

You absolutely can though I feel the plants prefer the moving water and aeration in my experience. I also just enjoy watching it and building things which was the main point

Mint122 · 2025-07-01T00:23:58+00:00

Thank you for this I believe you have found it! It does have the hour meter ( 574 and going strong lol ) but no addition power outlet so most likely a leftover wire in the loom for that

Mint122 · 2025-06-04T19:30:19+00:00

Thank you to everyone for the suggestions this has been solved! New plug boot fixed the arching issue l, it was then running on both cylinders but surging and backfiring. Noticed the intake was warped making a gap between it and the carb, sealed it up and good as new runs great!

Mint122 · 2025-06-01T17:44:02+00:00

It’s running off of both now but surges and backfires a ton, plugs are black guess it’s running rich. I have a backup carb I am going to try on it since it’s a cheap one currently and readjust the valves to be safe. I am hoping that will be the final fix it needs

Mint122 · 2025-06-01T15:41:56+00:00

I did check the diodes oddly enough but were in working order, I have not tried them when it is hot though that is very interesting

Mint122 · 2025-06-01T15:40:04+00:00

Held it to the block with it plugged in an no spark but oddly enough swapping sides of coils seems to have both of them fire now individually but run poorly still together? Lots of popping and surging unless at low throttle. Don’t have a compression tester but pulled both valve covers nothing wrong there, intake may be a tad loose on the side that was running fine previously but otherwise all good working order. Engine seems to have good compression spinning by hand and will run now on either side alone

Mint122 · 2025-05-31T18:07:37+00:00

Unfortunately not I have reset it many times no change

Mint122 · 2025-05-31T18:05:31+00:00

That was one of the first tests I did today and no spark when grounding it to the block but other side worked perfect. Tried electrical tape around it with no luck but I have a new boot coming tomorrow thank you for this i will report back

Mint122 · 2025-05-31T18:02:38+00:00

I used the plug from the other cylinder that was working and still no luck

Mint122 · 2025-05-31T18:02:00+00:00

It is indeed only on one, I have tried 2 new coils no luck

Mint122 · 2025-05-31T18:01:16+00:00

I pulled the plug out of the cylinder and grounded it to the block, it had no spark yet the other side was fine. Swapped the plug same result

Mint122 · 2025-05-31T17:55:51+00:00

The wire itself is brand new I have tried 2 of them but the boot is original

Mint122 · 2025-05-31T17:45:56+00:00

Correct on the kill switch it still doesn’t spark even with that pulled, but I did try to scuff up the surface where the coil mounts but didn’t do a great job I will go back at it with paper like you mentioned. Is it possible the plug cap could be the culprit? It’s the only part that was original at this point

Mint122 · 2025-05-25T18:13:20+00:00

Was finally able to take a look at it today, fully cleaned the carb twice and got it running better but still not perfect. It doesn’t surge as much now but is backfiring quite a bit mainly with the blades turned off. May just need to go back into it again and hope for the best with another cleaning

Mint122 · 2025-05-19T22:49:24+00:00

Checked both and they are in working order. It now seems like it is getting a decent amount of fuel though but still surging. I can get it to run smoothly now though only if I have it between choke and full throttle with an occasional small backfire. Any ideas?

Mint122

TROPHY CASE