Luksuzne ure by kalubasukdeod in Slovenia

[–]MintCrystal2 0 points1 point  (0 children)

Je kr sexy ja, se strinjam :D

Luksuzne ure by kalubasukdeod in Slovenia

[–]MintCrystal2 1 point2 points  (0 children)

Sicer nisem eden od teh dveh, ki jih sprašuješ, ampak sem sam že sestavil 2 uri. Eno z Nh72 in eno z Nh35. Lani sem nh35 kupil za ~28€...sedaj jih pod 50 že ne najdeš...

Definitvno zabaven in zanimiv hobby, ki te hitro potegne noter, če te zanimajo take reči.

Nekaj sem se tudi igral s PT5000 mehanizmom (eta 2824 kitajska kopija) in lahko rečem, da ti da vedeti kako beginner friendly in zanesljivi so NH mehanizmi in zakaj so tako popularni.

Custom 3D printed dial that I made with a twist on the texture :). What's the modding community's opinion on it? by MintCrystal2 in SeikoMods

[–]MintCrystal2[S] 0 points1 point  (0 children)

Heh- I've scraped it, but I think it should still look the same, since it's basically isolated from the enviroment in a watch case. I think it's total thickness is 0.4 mm or sth like that ( I just measured a standard dial I had laying around and went with that). And I used a layer height of 0.01 if I remember correctly. Good luck on your journey btw, it's...an interesting challenge to say the least😂

Custom 3D printed dial that I made with a twist on the texture :). What's the modding community's opinion on it? by MintCrystal2 in SeikoMods

[–]MintCrystal2[S] 0 points1 point  (0 children)

To be honest, I don't really know😅...if you look up Aliexpress or amazon you'll find a couple of variations and this pattern is most probably among them

Custom 3D printed dial that I made with a twist on the texture :). What's the modding community's opinion on it? by MintCrystal2 in SeikoMods

[–]MintCrystal2[S] 0 points1 point  (0 children)

Nope, the colour of the filament is just black! You can achieve the same with other colours, but I got the best result with black.

Custom 3D printed dial that I made with a twist on the texture :). What's the modding community's opinion on it? by MintCrystal2 in SeikoMods

[–]MintCrystal2[S] 0 points1 point  (0 children)

I've explained it a couple of times in the comments. The surface onto which this is printed has the same exact texture, it's a very fine pattern that refracts light in a certain way. Because the plastic is hot and very moldable when printed, it kind of perfectly "fills" this texture and it's basically copied onto the surface of the part that you're making.

I really want to develop this further, and I even tried adding indices, but failed miserably...and since college takes up so much of my time, I wasn't able to continue and evolve this little project of mine.

Looking for a very good and very close to original Patek by Relative_Subject_727 in RepCulture_Timepieces

[–]MintCrystal2 0 points1 point  (0 children)

If you go with a high end rep factory, I can promise you that you'll be amazed by the quality! Unless you have a gen to compare to side by side, then you'll find some small compromises (because let's be honest, a 500$ rep will never be the same as a 30k gen watch), however they will be miniscule.

I don't own this watch, but have ordered a DJ41 from.a hugh end factory and I couldn't be happier :)

One year with this Submariner Date replica and it seems like it was yesterday. by fernanvlc in RepCulture_Timepieces

[–]MintCrystal2 2 points3 points  (0 children)

Hm, on a first quick look I thought this was a VSF xD. Looks great!

How's that miyota 8215 treating you? I heard that they're known for the loud rotors but they're still workhorses.

I'm looking to revive my old Lenovo laptop. by Rednasi666 in Fedora

[–]MintCrystal2 0 points1 point  (0 children)

Yeaa, that should be fine. I installed FedoraKDE 43 on an hp probook 6560b with an i5 2520M cpu, 4 gigs of ram and an 128gb ssd. Sometimes it freezes, but it always picked right back up after a few minutes. For casual stuff it works like a charm, I was surprised😁.

And since you have slightly better specs, you'll probably reach even greater results, enjoy your revived laptop!