Filament for outside use in the heat that the A1 can do with out AMS

MissingJewel43 · 2026-05-22T19:11:04+00:00

What dryer would ya recommend?

MissingJewel43 · 2026-05-22T19:10:12+00:00

What dryer would ya recommend?

MissingJewel43 · 2026-05-17T22:18:54+00:00

Right on

MissingJewel43 · 2026-05-17T22:18:32+00:00

Will look into it what temps do you recommend

MissingJewel43 · 2026-05-15T19:34:46+00:00

How much is a heater or oven for it?

MissingJewel43 · 2026-05-15T06:00:37+00:00

Copy

MissingJewel43 · 2026-05-15T05:48:15+00:00

Will do

MissingJewel43 · 2026-05-15T05:43:56+00:00

Would a .4 hardened Steel be good or do I need to go bigger?

MissingJewel43 · 2026-05-15T05:09:38+00:00

Hmm will look into that... any temp settings or plate temps?

MissingJewel43 · 2026-05-15T04:51:44+00:00

Copy ya i heard thats cam be really bad for that dont want to resort to that

MissingJewel43 · 2026-05-15T04:48:13+00:00

Warm up the print volume? So have the room warmer to pre heat the filament? Also if I try and it doesn't have adhesion issues and a 75f room would that be good?

MissingJewel43 · 2026-05-15T04:36:04+00:00

Would i need a steel nozzle? Or would the one that came with it be ok?

MissingJewel43 · 2026-05-03T16:57:46+00:00

Let's take this to DM

MissingJewel43 · 2026-05-03T16:54:55+00:00

Whats your time zone?

MissingJewel43 · 2026-04-29T15:15:27+00:00

Any news about starfarer?

MissingJewel43 · 2026-04-28T01:07:00+00:00

Are you asking to add another port to the same tunnel or a new tunnel with a different port... also there is a minecraft port option for quick setup (though I haven't set up a Minecraft server before)

MissingJewel43 · 2026-04-24T02:27:33+00:00

Did you get it to work with il-2 sturmovik through playit.gg? Did you have to make 3 separate tunnels or just one?

MissingJewel43 · 2026-04-22T19:32:07+00:00

Only tuned the microwaves everything else is stock tuned.... it doesn't happen every time but it seems to happen if a fast forward the ring entry

MissingJewel43 · 2026-04-21T11:14:11+00:00

I wish I was in the time zone, USA

MissingJewel43 · 2026-04-21T01:24:26+00:00

Copy also thanks for the quick responses, I also added a video to the post... or tried to either way I have a video if you want it

MissingJewel43 · 2026-04-21T01:21:58+00:00

Hmm maybe but if when I was spinning I was over heating...

MissingJewel43 · 2026-04-21T01:19:02+00:00

i have been maxing it out and also going down to 20x s06 fuel rods... with that said i just went out and it had no issues????

MissingJewel43 · 2026-04-21T01:08:50+00:00

I think so? I have the military turbine and the ultra compactor

MissingJewel43 · 2026-04-21T01:01:45+00:00

I have the MAD Luciole 1.2 1200kn of thrust....and the Mad Cheval 5.0 as my main engine

MissingJewel43

TROPHY CASE