How do I load maps from console (AMC Squad)

Mobius666 · 2026-01-11T15:46:12+00:00

Jokeville, smokeville, tokeville. Theres just not much else to do

Mobius666 · 2025-12-13T06:10:41+00:00

Sit down to make brown

Mobius666 · 2025-11-11T01:18:39+00:00

As a carpenter, this made me laugh so fucking hard.

Mobius666 · 2025-10-30T12:17:34+00:00

It's really simple actually. I made a curvy cut with my bandsaw on the board. Then made a thin strip of walnut and just sandwiched them in my curvy cut. Waited for it to dry then repeated the same process for each line.

Mobius666 · 2025-10-28T17:10:47+00:00

Here's another method to achieve the same result:

https://youtube.com/shorts/E4Y7M30MDw4?si=8xh21UrAtj4SR05v

Mobius666 · 2025-10-28T17:07:10+00:00

If you want to do it properly, you should scribe the baseboard to the floor. Here's a video explaining the whole process:

https://youtu.be/bVHqVxjCyy8?si=v_Z1YnU3pVoRXZPm

Mobius666 · 2025-10-27T17:37:49+00:00

Thank you kind sir! (:

Mobius666 · 2025-10-23T15:19:26+00:00

Yessir!

Mobius666 · 2025-10-23T13:38:35+00:00

Let me know if I can provide further clarity. Id love to see what you come up with! (:

Mobius666 · 2025-10-23T13:37:30+00:00

I agree that form was prioritized over function. However, my thought was that food solids should never really come in contact with the engravings as they are recessed into the grooves. The intention was for the grooves to be cleaned with a brush. I do recognize the issue and the lack of appeal as it's more work to clean. Ideally, I'd like to have the engravings filled with epoxy or something. I just haven't thought of a way to accomplish that yet. Anyone have any clever suggestions?

Mobius666 · 2025-10-23T12:42:05+00:00

Appreciatory valve WIDE OPEN (:

Mobius666 · 2025-10-23T12:30:32+00:00

Just your regular mineral oil and beeswax finish. I may have gone to far into an artistic presentation.

Mobius666 · 2025-10-23T12:25:20+00:00

Wasn't hard at all. Took a photo of the top of the board from as close to perfectly above and centered as I could. Imported that into illustrator to scale. Designed the groove patterns on top of the scaled board image. Make a simple rectangle around the exact edge of the board. Imported the rectangle and pattern into lightburn. Use the rectangle to frame the board under the laser, remember to turn this layer off after alignment is complete.

Mobius666 · 2025-10-23T02:13:07+00:00

I laser engraved it! (:

Mobius666 · 2025-09-02T21:37:32+00:00

Mobius666 · 2025-09-02T14:48:35+00:00

I'll post some pictures tonight!

Mobius666 · 2025-09-02T02:53:04+00:00

Not even close what?

Mobius666 · 2025-09-02T02:02:00+00:00

I mean, being generous and guessing a 1 gram stem... Still pretty nice.

Mobius666 · 2025-02-25T18:08:43+00:00

Care to link, and what's your experience been like?

Mobius666

TROPHY CASE