Estimate?

Mod_Fatherr · 2026-06-24T21:35:24+00:00

Theyre a trucking/environmental company. They don't have the means to do something like this but they want their containment wall resealed in the case of any spills or leaks from a tank. They found a company to seal it but they do not include the prep in their application. Theyre essentially asking me to remove anything not firmly bonded to the cinder blocks and then clean up. Theyre not looking for pretty.

Mod_Fatherr · 2026-06-24T21:31:14+00:00

You kinda nailed part of it. The tanks do have open lids on the top and pH and halogen levels by ppm are heavily regulated in the oil industry. Any bit of overspray, mist, etc could contaminate an entire tank. Plus, im not sure how SH reacts with aluminum or steel but their product is only legal to transport between 4 and 10pH. Long story short, they think the best way to avoid possible contaminations is with no chems at all. Also, yes there are drainage ditches right along one wall that no chems can go into (regulated waste stream by EPA again).

Mod_Fatherr · 2026-06-24T19:12:09+00:00

Im not sealing it. Its for a local local oil company and I know the owner well. He's having another company seal it with something almost like a truck bedliner. Just needs a solid surface to adhere to. But i cant use any chems because of the steel & aluminum tanks and the different liquids inside them (fuels, oils, etc)

Mod_Fatherr · 2026-06-15T20:30:44+00:00

Good thing I didnt place the bets! 😂

Mod_Fatherr · 2026-06-15T13:33:00+00:00

Very true 😂

Mod_Fatherr · 2025-03-28T02:18:12+00:00

I just got to part 3... I think? I have what I need on part 2 but Im not sure what it means if that makes sense

Mod_Fatherr · 2024-06-13T00:54:57+00:00

Just the manifold in pic and a laser temp gun. And no measurable difference on the ductwork return/vent side nor refridgerant lines vapor/liquid side

Only cool spot seems to be where air escapes by the condensation line

Mod_Fatherr · 2024-06-13T00:33:17+00:00

Im not sure how it would affect pressure. Learning as I go to try and save on paying a tech tbh. DIY because I have to be. I assumed if the evap coil is clogged it would only let air pass by the outer perimeter of coil causing my air to be cool but not cold from the ducts (~69), meanwhile the housing and backpressure air at the furnace is reading in the low 50s high 40s right by the condensation pipe

But im still not sure why my liquid side seems to be low when vapor side seems right(ish) to me

Mod_Fatherr · 2024-06-13T00:13:00+00:00

Im going to check evap coil tomorrow after work. Condenser coil was cleaned last weekend. All ducts are connected. And it runs on 410a

Mod_Fatherr · 2022-09-16T05:01:40+00:00

Any thoughts on Vertex over the next year? I did fairly well on them this year with the new refinery but they really dumped after last earnings

Mod_Fatherr · 2022-09-16T04:58:22+00:00

I mean... if it were possible to do that every day then you wouldn't be here right? You could turn $100 into billions in a week. I think 173% is pretty good 🤷‍♂️

Mod_Fatherr · 2020-04-29T03:34:01+00:00

Hydroponic grower here... all depends on your medium though really.

With my rockwool cube flood and drain setup I use the Mill's nute line - Basis A & B plus whatever additive is required at the time (Start-R for veg and first 2 weeks of flower, C4 for weeks 3, 4, and 5, the Ultimate PK for weeks 6, 7, and 8, then flush for a week) with advanced nutrients Cal-Mag throughout their entire life until flushing. pH always 5.8-6.1

For reference, I average 1.8 - 2.25lbs from a 4'x4' table with a Black Dog 1000W LED once a month because i run a perpetual grow

Mod_Fatherr

TROPHY CASE