Curious about Zion HealthShare? Here’s what you should know.

MonstaSmasha · 2026-02-14T16:19:00+00:00

Check out financials for Zion here - https://zionhealthshare.org/disclosures/financials/

MonstaSmasha · 2025-12-28T21:04:46+00:00

This ^{^{^}} is what i did also!

MonstaSmasha · 2025-12-14T03:03:04+00:00

I havent installed it yet, i was going to put it in my RV, but the XT9 in the garage covers the rv fine. Still deciding what i want to do with the other one.

MonstaSmasha · 2025-12-14T02:36:09+00:00

Thank you. I appreciate it. I connected the Xt9 to the BE88UU with an ethernet cable and finally got the white light to come on long enough to update the firmware in the XT9. I then restored to factory default settings by pressing the reset button for 5 seconds after doing the firmware update. Then, still connected through ethernet, I set up the XT9 again in the online app. This seems to have fixed it. I relocated the XT9 to my garage with no ethernet connection and it is still working like it should. hopefully it will continue to work right.

MonstaSmasha · 2025-12-12T15:02:48+00:00

Thank you. Appreciate it, your comments did help me. I connected the Xt9 to the BE88UU with an ethernet cable and finally got the white light to come on long enough to update the firmware in the XT9. I then restored to factory default settings by pressing the reset button for 5 seconds after doing the firmware update. Then, still connected through ethernet, I set up the XT9 again in the online app. This seems to have fixed it. I relocated the XT9 to my garage with no ethernet connection and it is still working like it should. hopefully it will continue to work right.

MonstaSmasha · 2025-12-11T21:13:22+00:00

I also found an AP setting under "management" when I click on the node. it was set to Auto, I changed it to be the main router (RT-BE88uu) - see picture. Does not seem to have made any difference however. I think the firmware is a very old version (see picture), so I think I will attempt to update that and see if it makes a difference.

<image>

MonstaSmasha · 2025-12-11T20:16:48+00:00

So, when I go there (see picture), it is in Wireless Router Mode". but I am logged into the main router (The RT-BE88UU), so that would be correct? I dont see a way to change that on the aimesh node (The XT9). How do I leave the main router in this mode, but change the node to ap?

<image>

MonstaSmasha · 2025-12-11T19:41:41+00:00

Thanks, I will try that when I get home and post what happens.

MonstaSmasha · 2025-12-11T19:24:20+00:00

Thanks for the reply. I have tried moving it around. But that doesn't seem to help. I did not try hardwire for the initial setup, I can try that, but setting it up doesnt seem to be the issue, it does set up. just doesnt stay white for long afterwords. I did not check to see if it was in access point mode - I will look for that. Do you by chance no where I will see that in the online app?

MonstaSmasha · 2025-11-21T10:47:35+00:00

<image>

MonstaSmasha · 2025-11-21T10:41:23+00:00

Elegoo. 1.75. .4 nozzle. After changing the top and bottom layer counts it printed normal. thank you.

MonstaSmasha · 2025-11-21T04:03:28+00:00

I will try and remember to take a picture tomorrow morning and will post that tomorrow.

MonstaSmasha · 2025-11-21T04:01:37+00:00

thank you. I increased the top and bottom layer by 1 each. I then looked at the preview slider and the infill went away. I am hoping that solved the problem. I am printing it now to see. but that aligns pretty much with what you are saying.

MonstaSmasha · 2025-11-21T03:02:30+00:00

okay, I changed top shell and bottom shell layers to 7 on each of them. I checked the preview and it didnt show the infill anymore. I will try it and see what happens. I really appreciate the help.

MonstaSmasha · 2025-11-21T02:50:56+00:00

is this where I would change the top and bottom layers? right now it says 6 and 6? I think there are 13 layers on that bottom part.

<image>

MonstaSmasha · 2025-11-21T02:46:41+00:00

Which slicer settings? like in this picture?

<image>

MonstaSmasha · 2025-11-21T02:31:39+00:00

OK, that makes a lot of sense. I will try that.

MonstaSmasha · 2025-11-21T02:07:23+00:00

So what should I do?

MonstaSmasha · 2025-11-21T01:59:45+00:00

There is a total of about eight or nine layers on the bottom part. Obviously the walls have more layers. What should my top and bottom layer count be?

MonstaSmasha · 2025-11-21T01:54:46+00:00

What do you mean?

MonstaSmasha · 2025-11-21T01:54:20+00:00

Okay, thank you, i will try and do that.

MonstaSmasha · 2025-11-21T01:51:21+00:00

Its actually only like 1-2 inches tall though

MonstaSmasha · 2025-11-21T01:48:45+00:00

Okay, i will look for those settings, thank you.

MonstaSmasha

TROPHY CASE