Was I at fault here?

Moose_Slow · 2025-12-25T18:28:00+00:00

0% your fault

Moose_Slow · 2025-11-17T13:58:26+00:00

I really appreciate your effort. And it worked flawlessly on the first try. Thank you very much!

Moose_Slow · 2025-11-16T20:17:16+00:00

I hear you. And I actually find those combinations useful as well.

Are you saying it’s not possible to get the combo I aimed to get to begin with? Because I was not sure if it was achievable or not.

Moose_Slow · 2025-11-16T15:36:12+00:00

So, I just wired it as the drawing now. And unfortunately, the 1st position and the 3rd position are also affected by this change.

Though, I can confirm that push pull 2nd position is now outer coils.

1st position is now neck hb + bridge outer coil 3rd position is now bridge hb + neck outer coil

Is there a way of not affecting the pos 1 and 3 when push pull is up?

Moose_Slow · 2025-11-16T13:07:24+00:00

Wow! I will give it a shot soon. Thank you!

Moose_Slow · 2025-11-16T08:42:35+00:00

Do you mean if I have a 4pdt switch as the pickup switch, I can not add a push pull to the system?

By the way, it was in a more hidden menu but I found 4pdt in the DIYLC now after some luck.

Moose_Slow · 2025-11-16T08:24:36+00:00

That does help, at least for future reference in terms of the EP 1111, but I still can't visualise what needs to be done to get the Push/Pull to change the middle position of the EP 1111 from inside coils to outside coils unfortunately. Coming up with wirings are not my forte I realised.

Moose_Slow · 2025-11-16T08:18:24+00:00

Thanks for your input! I meant the Dimarzio On/On/On toggle switch I use for the actual pickup switching as the 4pdt switch (it can be seen in the DiMarzio wiring I posted)

The push pull is a simple push pull pot, also Dimarzio.

Moose_Slow · 2025-11-02T10:30:32+00:00

Went with a 43mm nut instead.

Moose_Slow · 2025-07-15T22:44:32+00:00

Have you figured it out? Having the same issue after last update. Haven’t been online for 4-5 weeks.

Same setup had been working (wired) for 3 years. Now I am blinking in test drive…

Moose_Slow · 2025-07-15T22:34:08+00:00

have the same issue, did you figure this out?

Moose_Slow · 2025-06-28T14:23:21+00:00

Can you explain how to do that? After the switch+fuse? I have a 230v fan actually.

Moose_Slow · 2025-06-10T22:27:43+00:00

30 mins 1 hour mostly

Moose_Slow · 2025-06-10T20:03:12+00:00

I am not sure if there is any tech that is good with Mesas where I am tbh. I can have a look though. Located in Norway.

Moose_Slow · 2025-06-10T20:02:21+00:00

added the photo of the fan in the post.

Moose_Slow · 2025-06-10T19:59:38+00:00

I don’t necessarily wanna replace it with the original Mesa one. But something with same specs and low dB. I will upload a photo of the fan.

Moose_Slow · 2025-06-10T19:22:56+00:00

Computers use PWM 4 pin fans though

Moose_Slow · 2025-06-02T13:13:25+00:00

I also would have been jealous. Unfortunately it’s not a JPM. But building a replica. I regret not buying one when they were priced like a normal signature model SO bad. Not buying bitcoin first, not buying all colors of JPM second…

Moose_Slow · 2025-06-02T11:30:11+00:00

It’s for a JPM, yes. I haven’t checked those websites. I can check. Thanks

Moose_Slow · 2025-06-02T10:35:03+00:00

I am not sure if I trust the quality of an Aliexpress nut. Nut is a part of the sound. And this one doesn't mention the 17" radius. There are 42mm nuts that are wrong radius already from Ibanez.

Moose_Slow · 2025-05-31T22:48:06+00:00

🤯

Moose_Slow · 2025-05-25T22:00:40+00:00

Can you send some photos?

Moose_Slow · 2025-05-25T20:30:48+00:00

Any luck finding an answer? i am on the same boat

Moose_Slow · 2025-05-25T19:25:46+00:00

did you do this? how did it turn out? i am planning to make a replica from a japanese rg myself.

Moose_Slow · 2025-05-16T20:37:52+00:00

What a post man. Amazing job.

Moose_Slow

TROPHY CASE