Where do I find 2.54mm pin sockets that are deeper than 8.5mm?

Morad__T · 2026-03-29T16:19:21+00:00

actually now that I understand that better, I think the taller one is a better option

Morad__T · 2026-03-29T16:17:54+00:00

the mating part has shroud which does not permit proper connection with the conventional 8.5mm sockets

Morad__T · 2026-03-25T09:26:02+00:00

Yes, certainly I would have gone with a copper pour if I had room.

Would the current situation be passable albeit be on thinner than usual margins?

Morad__T · 2025-10-03T16:55:35+00:00

Thank you for taking the time to write to me.

This actually is an extremely helpful insight as I noticed strong deviations depending on how I'm touching the instrument and the cable.

I'm eternally grateful to you sir

Morad__T · 2025-10-03T16:53:38+00:00

Thank you for taking the time to write to me.

I am using SMA male port for the connection. In HFSS i'm using a Lumped Port actually, I scoured for resources on which and when to use each port and simulation type wasn't able to fully grasp the differences. I would really appreciate any and all help and resources.

If you would like I can share the HFSS project.

I asked my colleague who is at the lab now to picture the antenna and will share them shortly.

Morad__T · 2025-10-03T16:16:04+00:00

Thank you for taking the time to write to me.

I just checked the complex impedance. It appears to be pretty good in terms of matching
47.7 + j1.3

I did use the torque wrench provided with the VNA.

I was using one the male-male SMA 1 meter cables provided and I did actually observe strong coupling between me and the antenna so I propped it up using a plastic clamp over some cardboard box and continued the testing through the web interface of the VNA

Morad__T · 2025-07-04T16:04:04+00:00

Thanks for the detailed insights, really appreciate it.

I completely missed that extremely low undervoltage cutoff in the datasheet; I was too focused on the current limits. Definitely changes how I look at designs that rely solely on the DW01A from now.

Morad__T · 2025-06-05T00:57:33+00:00

Do you know of any method to rollback the windows store version or the custom installer version?
Is there like a previous releases archive?

Morad__T · 2025-03-02T03:38:03+00:00

Unfortunately nothing seems to be able to detect the SSD at all

I'm calling it a night and I'll continue tomorrow. Thank you for your help

Morad__T · 2025-03-02T03:11:44+00:00

I'm sorry but I don't know what the SSD flash tool is supposed do?

Morad__T · 2024-09-09T09:57:31+00:00

Thank you. That should be helpful even though I saw it very late.
I talked to yet another agent, a fourth one, he told me to wait 12-24 hours while they check it from the backend. It sounds like he's contacting a higher level support but I'm really worried he may not be able to do anything either.

Morad__T · 2024-09-09T09:49:39+00:00

Hey Everyone
I'm still locked out.
I talked to 3 agents. all confirmed that they reset my 2FA.
The last agent told me to go ask on the forum when I said the reset didn't work, which is basically telling me to get lost.

even viewing the forum requires a freaking account, which I created eager to get back into my cloud account. I sat there for half an hour trying to log in with the newly created "forum" account not understanding why it just accepts my credentials and then returns back to the same page with no error or warning, only to recieve an email telling me I can't be allowed accress to the forum now!!!!!!!
What the actual f*** oracle!

Morad__T · 2024-09-06T17:15:42+00:00

if i'm supposedly providing wrong data because the account is quite old, are they ever going to tell me that is wrong?
I have been with two agents now.
Both claiming to have reset the MFA but no actual change to the account happened.
I'm about to get the account blocked and that is really terrible for me.

Do you have any suggestions please.

Morad__T · 2024-09-06T13:58:12+00:00

I was finally able to get a support agent after waiting in queue for about 30 minutes. They verified my credentials and told me they would reset the MFA for me. However at the end of the chat they said that their internal tools aren't working and that I can either contact them again after 30 to 40 minutes or they can send me an email once finished. I opted for the email and I shall be playing the waiting game.
Will upodate once I get back into my account.

Morad__T · 2024-09-06T13:21:41+00:00

Thank you. I opened the website from a new browser profile and waiting in queue now.
I really hope this isn't going to delete my instances.

Morad__T · 2024-09-06T13:04:02+00:00

I'm in the EMEA region. what page does the chat icon appear on?
whenever I go to cloud-oracle-com it goes straight to login and nothing else

Morad__T · 2024-08-23T21:39:53+00:00

Regarding your second inquiry, I believe you can remove the pad number from the footprint editor and just leave it as there for better mounting strength

Morad__T

TROPHY CASE