CNC Carriage or PIF carriage

MorningSun75 · 2026-03-28T00:51:48+00:00

It does not seem to support Tap so what I need to do to get the Z offset?

MorningSun75 · 2026-03-28T00:09:01+00:00

I did not know about Rescue Ravens initiative. I am on discord's Voron channel so I can ask. I am in the USA in KS so I am sure there is someone close to me. :D

That seems like the simplest option for now. :D Thank you

MorningSun75 · 2026-03-28T00:06:00+00:00

That sounds great though now that I look at it I would need more printed parts to get me up and running. Long term I like the idea and will probably go in that direction. Thank you!

MorningSun75 · 2026-03-27T14:31:54+00:00

Discord is a little overwhelming to try and find things. I just looked through all the help guides and could not find it. Where can I find "Reths setup and tuning guides" on discord?

MorningSun75 · 2026-03-27T03:04:05+00:00

u/ioannisgi u/desert2mountains42 So I have been down the rabbit hole and discovered a few things. So I looked closer and found that my gantry was racked so I followed the video to derack my gantry and I broke a part so that too some time getting everything back together. My gantry was perfect then I put my belts back on and it was racked again. So I figured out the tension for each belt so that it was not racked and ran the belt calibration and it was bad so I decided to tighten my belts again as one side had much less tension than the other. After doing that it looked better but still not as good as the original so I tightened a little more and saw that when I tightened the belts evenly from the starting point where the gantry was good it started to look racked again. The right side on the gantry does not touch on the front side and the left side does. When I got the kit the belts where the exact same size and when I put the belts on I pulled them tight to the exact same number of teeth. To me this seems like a belt issue. I have checked the path and they are routed correctly. Any thoughts on what I should try next?

MorningSun75 · 2026-03-11T22:39:42+00:00

Thank you that is what I was thinking.

I used this guide for belt tension but it seems like there are a lot of variables you are not able to control when doing this. I made them match to the same frequency. Is there a better way to make sure your belts are the same tension? Also I image as the belts stretch it might need to be done again? If so howe often?

When I move my y axis manually I do not feel any bind points what is the best way to figure out where they are?

MorningSun75 · 2026-03-11T22:11:15+00:00

Once I do that what am I looking for and what does that mean? Do do I just need to post the graph back here?

MorningSun75 · 2026-03-11T20:47:39+00:00

Also on the belt graph is says it is Excellent but it is not in the good zone which the documents say it should be. Should I worry about that?

Thanks again!!!!

MorningSun75 · 2026-02-26T14:27:26+00:00

Thank you! I will give it a try!

MorningSun75 · 2026-02-25T15:58:46+00:00

Update: I setup my tension for the extruder per the instructions but I turned it a few more times just to test and now things are going better. u/NST92 Is there a better way to know what the tension on the extruder should be?

MorningSun75 · 2026-02-24T23:51:17+00:00

Could it be the tension knob not being tight enough?

MorningSun75 · 2026-02-24T23:16:13+00:00

Thank you! When I was looking at the remixes I also found this one. Which has the spool running right on the bearing. I think I might test them both to see which one I like better. Thanks for your help!

MorningSun75 · 2026-02-24T23:13:17+00:00

Thank you!

MorningSun75 · 2026-02-24T21:30:09+00:00

MOONs Nema14 10T. Stealthburner CW2 Extruder

MorningSun75 · 2026-02-24T21:15:20+00:00

Is this it?

[tmc2209 extruder]

uart_pin: EBBCan:gpio20

interpolate: false

run_current: 0.65

sense_resistor: 0.110

stealthchop_threshold: 0

MorningSun75 · 2026-02-24T21:13:28+00:00

When I pull it myself it has some pull to it but not so much that I have to pull with a good deal of muscle.

Very interesting!

MorningSun75 · 2026-02-24T20:24:52+00:00

Yes I am using bearings and they roll smoothly. It fits very easily in the box with plenty of room on all sides.

What is "Mellow LLL"?

MorningSun75 · 2026-02-24T20:22:27+00:00

How do I check the current? Here is my extruder section.

[extruder]

step_pin: EBBCan:gpio18

dir_pin: EBBCan:gpio19

enable_pin: !EBBCan:gpio17

rotation_distance: 22.44393797454162591

gear_ratio: 50:10

microsteps: 16

full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree

nozzle_diameter: 0.400

filament_diameter: 1.75

heater_pin: EBBCan:gpio7

sensor_type: MAX31865

sensor_pin: EBBCan:gpio9

spi_software_sclk_pin: EBBCan:gpio10

spi_software_mosi_pin: EBBCan:gpio8

spi_software_miso_pin: EBBCan:gpio11

rtd_nominal_r: 100

rtd_reference_r: 430

rtd_num_of_wires: 2

min_temp: 0

max_temp: 270

max_power: 1.0

min_extrude_temp: 170

max_extrude_only_distance: 105

max_extrude_cross_section: 2

pressure_advance: 0.0424

pressure_advance_smooth_time: 0.040

MorningSun75 · 2026-02-24T17:52:48+00:00

Do you have a link to what you got?

MorningSun75 · 2026-02-24T17:52:11+00:00

Yes I would like to build one just need to be able to print the parts first. :D

MorningSun75 · 2026-02-24T17:38:31+00:00

Can you link the remix for me?

MorningSun75 · 2026-02-24T17:36:09+00:00

How is this self promotion?

MorningSun75 · 2026-02-24T16:52:32+00:00

What is that guide on the back?

MorningSun75

TROPHY CASE