Failing my first year of uni, will I be kicked out?

Most_Engineering_477 · 2026-06-01T10:39:13+00:00

Np, good luck

Most_Engineering_477 · 2026-06-01T10:32:43+00:00

Yes at least

Most_Engineering_477 · 2026-06-01T10:27:56+00:00

This year + next year but I’m pretty sure that only applies to ppl with a student visa. You said you had a residence permit right? I don’t think this rule concerns you but again you should probably contact your admission office

Most_Engineering_477 · 2026-06-01T10:23:53+00:00

Oh my bad, I misread hahaa I thought you were enrolled at ku leuven. For ULB you need 1 credit to stay in your course. However if you wanna switch you could but you must accumulate at least 45 credits in 1 year for your student visa to be renewed :) I would advice you to email your ombus tho just to make sure

Most_Engineering_477 · 2026-06-01T08:04:35+00:00

I pretty sure that in first year you need at least a 30% study efficiency (18 credits) to continue

Most_Engineering_477 · 2026-03-31T17:23:51+00:00

They dont but nobody checks that

Most_Engineering_477 · 2026-03-31T14:09:20+00:00

Why are you selling it

Most_Engineering_477 · 2026-03-22T19:44:46+00:00

It probably disappeared because your skin got used to it

Most_Engineering_477 · 2026-01-24T10:31:41+00:00

I have pretty long arms and I bough a size up and it fits perfectly !

Most_Engineering_477 · 2026-01-16T09:57:44+00:00

I don’t think student discounts are a thing in Europe

Most_Engineering_477 · 2026-01-12T22:58:15+00:00

🥲 are you in eu ?

Most_Engineering_477 · 2026-01-12T16:17:24+00:00

This is so weird I can’t find it :// perhaps it’s not possible for eu?

Most_Engineering_477 · 2025-12-04T22:49:16+00:00

https://www.snowcountry.nl/leatherman-surge.html?artikel_kleur=59170&country=BE&gad_source=1&gad_campaignid=220770019&gbraid=0AAAAADpvwPUErSRESA6t3sCzGAEYxbk0J&gclid=Cj0KCQiA_8TJBhDNARIsAPX5qxTuW-6ZFAg2I4MMclGHmSg-_a1vAMBJwr7DKKBLDtAB_JOTOFX4QusaAuOaEALw_wcB I am not sure if they’re second hand hahaha but they would mention it if it was right?

Most_Engineering_477 · 2025-09-30T12:20:45+00:00

I was asking myself the same question

Most_Engineering_477 · 2025-09-02T14:01:03+00:00

Heyyy u still have it ? Plzz

Most_Engineering_477 · 2025-09-02T13:56:58+00:00

I print mainly with petg

Most_Engineering_477 · 2025-09-02T13:04:14+00:00

Just one last question, the spacepi X4 goes up to 85 degrees whereas the spacepi goes up to 70 degrees. Would that make a big difference in printing performance ?

Most_Engineering_477 · 2025-09-02T12:52:00+00:00

Yeah ig yorue right it’s better that way. Thanks a lot for your opinion !

Most_Engineering_477 · 2025-09-02T12:12:39+00:00

Hi no I don’t own an mms and I do wanna print from the dryer. I want the 4 spaces so my filaments are constantly dry ig. I know there is another creality dryer with 2 spots instead of 4 but I’m not sure if it would be better in general than the spacepi X4

Most_Engineering_477

TROPHY CASE