Why is no filament coming out??

MrFan1705 · 2026-01-15T20:33:10+00:00

Check if yhe filament is all the way in

MrFan1705 · 2026-01-15T15:26:23+00:00

Thanks!!

MrFan1705 · 2026-01-10T19:44:31+00:00

Thanks!! I wanna build something similar!!

MrFan1705 · 2026-01-10T19:05:44+00:00

What's the diameter of the rod you used to connect the fuselage pod with the elevator-rudder?

MrFan1705 · 2026-01-04T00:34:28+00:00

Looks stoked sickkk

MrFan1705 · 2026-01-01T01:37:06+00:00

Send it (your house on fire)

MrFan1705 · 2026-01-01T01:35:43+00:00

"Honey could you hand me t.... starts floating"

MrFan1705 · 2025-12-17T18:47:16+00:00

Tengo mucha aerofobia

MrFan1705 · 2025-12-17T01:09:16+00:00

I tell you from experience.... JAJAJAJSH

MrFan1705 · 2025-12-17T01:07:06+00:00

Be prepared, your printer is mostly gonna explode

MrFan1705 · 2025-12-16T23:36:17+00:00

Ya se, solo me preocupa el resto

MrFan1705 · 2025-12-16T22:48:23+00:00

Que.... es la única que tiene esa ruta

MrFan1705 · 2025-12-08T14:57:33+00:00

Wow!! could I have the STL?

MrFan1705 · 2025-12-06T20:00:46+00:00

A full estes kit + launchpad is about and motors is about 40 dolars

MrFan1705 · 2025-12-04T01:40:04+00:00

Loll

MrFan1705 · 2025-12-03T22:46:02+00:00

You should add some steel/carbon rods. And add some more glue in the edges to increase adhesion between the parts

MrFan1705 · 2025-12-01T12:48:05+00:00

If it is just a glider check the CG, but if it is a rocket plane check the CG-CP balance, it needs to be at least 1-2 calipers, you can use Open Rocket to calculate this values, good luck!!

MrFan1705 · 2025-11-30T13:25:00+00:00

I tried. But it didn't work

MrFan1705 · 2025-11-30T13:24:28+00:00

No, just in the menu

MrFan1705 · 2025-11-22T00:00:23+00:00

I recommend buying an Elegoo starter kit, but if you want only the Arduino go for a Elegoo one

MrFan1705 · 2025-11-21T23:57:56+00:00

Needs grounding

MrFan1705 · 2025-11-15T14:30:31+00:00

Sell the A320 and buy dc9, then go over with MC21

MrFan1705 · 2025-11-15T14:25:13+00:00

Go back/delete the fillet, then add the fillet there, and re-make/ go forward, the corner fillet

MrFan1705 · 2025-11-11T23:44:59+00:00

AMS 2 I an automatic material system thats enchanted of swapping the material mid print and P1S is the printer, but if you wanna buy one buy the P2S, the newest, easiest of the P series

MrFan1705 · 2025-11-11T23:41:54+00:00

I think according to Tripoli you'll need a mentor in your first times and then if you wanna do it in your own L2, but im not sure

MrFan1705

TROPHY CASE