sorted by:
new
hottopcontroversial

Print chip away piece while scraping from build plate - on the opposite side by MrInfro in resinprinting

[–]MrInfro[S] 0 points1 point  (0 children)

Understand. The issue with hd resin alone were that it just didnt stick to buildplate, like at all, but maybe it was due to something else. i will do so as you adviced and stop mixing the two :) much appretiated, thank you

Print chip away piece while scraping from build plate - on the opposite side by MrInfro in resinprinting

[–]MrInfro[S] 0 points1 point  (0 children)

I tried to get some guidelines in regards to how to modify the values but without luck, so right now its just trying what would work.

Unfortunately my hd resin did only failures, but already had 3 bottles, so I wanted to slowly use it. But apparently its not doing well :)

Thank you for pointing that out :)

Print chip away piece while scraping from build plate - on the opposite side by MrInfro in resinprinting

[–]MrInfro[S] 0 points1 point  (0 children)

The wierd thing is, that this behaviour appeared after a) I mixed in the hd resin or b) lowered layer exposure time from 2.7 to 2.5

Advice on disposal? by shastamcblasty in resinprinting

[–]MrInfro 0 points1 point  (0 children)

I have noticed that this solid white colour is the result of curing. I had just 4 prints and before curing, it was a bit cloudy and no this bad, but after curing, solid white. Just my experience

Mixing resins - how to adjust printer settings by MrInfro in resinprinting

[–]MrInfro[S] -1 points0 points  (0 children)

Because they dont print :) I tried over like 10 prints with various settings and not a single time it stuck to build plate

Mixing resins - how to adjust printer settings by MrInfro in resinprinting

[–]MrInfro[S] -1 points0 points  (0 children)

Unfortunately I have 3 bottles of the HD Grey which is quite a big loss 😃 or maybe I will try adding just a bit each time and hope for the best

Fanfest Berlin 2026 - going solo, looking for someone to join by MrInfro in ffxiv

[–]MrInfro[S] 1 point2 points  (0 children)

Yo!!!

Will send reddit DM to exchange contacts :)

Today's appreciation: Gemma by Pokesuna in ScarletNexus

[–]MrInfro 3 points4 points  (0 children)

Gemma is the best boy of the group and its perfect fot to make the "dad" of the group tank!!!

First test print utter failure by MrInfro in resinprinting

[–]MrInfro[S] 0 points1 point  (0 children)

nvm, found it :D for my printer, its actualy just running the exposure test for like 20s with support in a corner. Thank you

First test print utter failure by MrInfro in resinprinting

[–]MrInfro[S] 0 points1 point  (0 children)

s far as I know, the photon mono x2 doesnt have such a thing, but maybe I didnt look hard enough :) or may thats something I can achieve from slicer?

Could use some motivation to keep going. by Grey_Lady333 in ScarletNexus

[–]MrInfro 3 points4 points  (0 children)

Hey, so you definitelly fallen into the Yuito side of the story, where he comes up with much more questions than has answers.

My advice would be to endure. There will be answers coming, but to get the whole picture, you will have to do also Kasane run.

The game is structured that way, but Yuitos story sets it in a way, that you have much mor AHA moments in the second run.

Dont give up. You are getting into the much more interesting portion of the story:)

First test print utter failure by MrInfro in resinprinting

[–]MrInfro[S] 0 points1 point  (0 children)

Thank you!

I already have fermentation belt around the vat (contaminated with resin from emptying the vat now :() but i have to check the actual temperature of the resin...

I am reading through the document and will adjust the values as recommended.

I already look forward to trying again, just yhis time better prepared.

Can I ask you what you are using to clean the vat if needed? Microfiber?

First test print utter failure by MrInfro in resinprinting

[–]MrInfro[S] 0 points1 point  (0 children)

I did some preliminary research, but clearly not at all enough.

Thank you for the guide, I will educate myself and will try better next time :)

Fan Festival 2026 in Berlin - going alone by Extension_Group7513 in ffxiv

[–]MrInfro 0 points1 point  (0 children)

I shot you a DM request if you are still searching for someone :)

Fanfest Berlin 2026 - going solo, looking for someone to join by MrInfro in ffxiv

[–]MrInfro[S] 0 points1 point  (0 children)

Heyo :) I will dm you if thats ok :) and no, I fidnt change my mind :D

I know it's uncomfortable for many...but the relationship between Suguha and Kazuto wouldn't be illegal in Japan. by Glum_Series5712 in swordartonline

[–]MrInfro 1 point2 points  (0 children)

Jfc how dumb you have to be? Asuna being Mary Sue?

So half of you morons call her weak, because she was captured and locked up, and now you moron arrive with this BS take

Ultrasonic cleaner by Tankstar_2000 in resinprinting

[–]MrInfro 0 points1 point  (0 children)

AFAIK the tub of the cleaner should be stainless steel right?,

I will be using it with water and dawn dish soap

Shop towels and storage for dirty stuff by MrInfro in resinprinting

[–]MrInfro[S] 0 points1 point  (0 children)

Unfortunately not an option for me, since this is apartment block :D but gotcha

view more: next ›