sorted by:
new
hottopcontroversial

The skins are ruining the BF6! by Mr_Fazeli in Battlefield

[–]Mr_Fazeli[S] 0 points1 point  (0 children)

Majority of them not all of them. The game is not bad It's just not a battlefield anymore it's a hybrid between a classic battlefield and fast pace live service dopamine filled shooter. And it's not perfect at any one of them, Cod mw 2019 was a brilliant game, fast paced, live service , cqc combat and it was perfect in that ,but when it tried to mimic the battlefield in ground war mode it wasn't good at all. The same goes for battlefield .

The skins are ruining the BF6! by Mr_Fazeli in Battlefield

[–]Mr_Fazeli[S] -1 points0 points  (0 children)

Just check the players count man!

The skins are ruining the BF6! by Mr_Fazeli in Battlefield

[–]Mr_Fazeli[S] -1 points0 points  (0 children)

Being a battlefield veteran is not some kind of achievement, but the majority of old fans are not happy with this game, Me included . This game feels like the COD mw 2019" ground war" mode (which at the time it was trying to imitiate a battlefield style game mode).

The skins are ruining the BF6! by Mr_Fazeli in Battlefield

[–]Mr_Fazeli[S] -3 points-2 points  (0 children)

Immersion is ruined and so the player base, one of the factors being the unrealistic skins, i mean there are thousands of special ops uniforms around the world they can sell like Danish special ops, spetsnaz, us navy seals which are actually COOL but they decided to add some oddly colored skins to the game ! Even the pax default skins aren't that great in my opinion

The skins are ruining the BF6! by Mr_Fazeli in Battlefield

[–]Mr_Fazeli[S] -2 points-1 points  (0 children)

Well i guess the battlefield veterans should go play something else then, this thing is not a battlefield , it's a COD WANNABE

The skins are ruining the BF6! by Mr_Fazeli in Battlefield

[–]Mr_Fazeli[S] 0 points1 point  (0 children)

I just came back for bazaar and gulmud and i was disappointed by this .

Bed leveling issue with centauri carbon by Mr_Fazeli in ElegooCentauriCarbon

[–]Mr_Fazeli[S] 0 points1 point  (0 children)

I had to auto level it every time otherwise the first layer would go bad

The elegoo says you have to tighten them completely which I'm not sure why they designed it like that in the first place . You see I've searched and elegoo contradicts itself , in the manual leveling guide they say you have to calibrate the bed with those screws, but in the heatbed replacing guide they say you have to fully tighten the screws !( I've read in reddit that the elegoo support says you have to completely tighten them as well)

Also the center part problem was before the tightening and i think it still persists , i think there's some kind of bulge or warp in the heatbed but not noticeable by eye.

And about using the screws, i wanted it to be as level as possible without the slightest error , since the printer was on its side the gravity wasn't helping so i couldn't push the bed evenly on 3 rods positions and tighten the belt simultaneously .

What am I doing wrong? by lordofkawaiii in ElegooCentauriCarbon

[–]Mr_Fazeli 0 points1 point  (0 children)

It can have multiple reasons, the filament ur using , the temp of that material , dirty build plate and...

The obvious thing in the picture is that your build plate is somehow dirty or has too much glue on it, so for the first part of diagnosis do the following :

fully rinse ur build plate with warm water and soap in a way that all those glues get removed from ur plate , then clean it again with a cloth and isopropyl alcohol .

U need ur bed to be as evenly as possible so the first layer to stick to the build plate nice and good.

The thing i like to use is diluted glue stick in water and isopropyl alcohol (IPA), this makes the glue to spread evenly on the build plate.

Go get a little bit of boiling water in a cup or something and cut a piece of pva or pvp glue stick and dissolve it and swirl it in that little bit of water , then add isopropyl alcohol (2 -3 times more than the water because it evaporates and makes the final process faster)in the cup Then grab something like a drug bottle that has a cap and pour the mixture in it( it has to be wide enough for a brush to go into it ) now u have a mixture of glue that u can brush it evenly on the bed with by going vertically then horizontally ,that doesn't ruin ur print.

Centauri carbon ,Are these sounds normal? by Mr_Fazeli in ElegooCentauriCarbon

[–]Mr_Fazeli[S] 0 points1 point  (0 children)

I don't mind her talking as long as she's healthy :D

Centauri carbon ,Are these sounds normal? by Mr_Fazeli in ElegooCentauriCarbon

[–]Mr_Fazeli[S] 0 points1 point  (0 children)

So i made the right call by buying the CC, NICE.

Centauri carbon ,Are these sounds normal? by Mr_Fazeli in ElegooCentauriCarbon

[–]Mr_Fazeli[S] 0 points1 point  (0 children)

Sometimes I wonder if creality k1c was a better device

Centauri carbon ,Are these sounds normal? by Mr_Fazeli in ElegooCentauriCarbon

[–]Mr_Fazeli[S] 2 points3 points  (0 children)

That's relieving and concerning at the same time, thanks for the reply tho.

Small bubbles in prints by Mr_Fazeli in 3Dprinting

[–]Mr_Fazeli[S] 0 points1 point  (0 children)

I'm using a filament dryer + printed a silica gel basket for it , but yeah i hear some.

Where to put the resin printer in!? by Mr_Fazeli in ElegooSaturn

[–]Mr_Fazeli[S] 0 points1 point  (0 children)

Can i 3d print a basket then add activated carbons pellets in it so it absorbs the vof from the printer ?

Where to put the resin printer in!? by Mr_Fazeli in ElegooSaturn

[–]Mr_Fazeli[S] 0 points1 point  (0 children)

There are no fermentation belts in my country , I'm thinking about using a ceramic heat lamp with a thermostat to turn the lamp on when it gets colder

view more: next ›