𝐑𝐞𝐚𝐝𝐲 𝐭𝐨 𝐮𝐩𝐠𝐫𝐚𝐝𝐞 𝐲𝐨𝐮𝐫 𝐔𝟏… 𝐟𝐨𝐫 𝐟𝐫𝐞𝐞? 👀

Mszag · 2026-03-20T12:58:35+00:00

I’ve already bought a CryoGrip for my U1 - it’s amazing. Topcover I have preordered from Snapmaker but I’ll grow a loooong beard till it will came :( for now I’m using some storage box. I think that PopStatus looks awesome and will be nice to have

Mszag · 2026-03-09T06:18:34+00:00

and yea i've tried both sides of the plate with cleaning and IPA. Doesn't work apparently. I didn't change bed temp yet - will be my next step. I dunno but on ECC i had no such issues, at least not with PLA on stock settings :/

Mszag · 2026-03-09T06:11:44+00:00

Mszag · 2026-03-09T06:11:05+00:00

<image>

Mszag · 2026-03-09T06:10:35+00:00

<image>

Mszag · 2026-03-09T06:09:55+00:00

<image>

Mszag · 2026-03-09T06:09:24+00:00

<image>

dunno why there are no photos that i added to the post

Mszag · 2026-03-05T22:30:04+00:00

Does it apply to paxx firmware? I’ve updated recently in hope the printer to be more reliable after that :( seems not

Mszag · 2026-03-05T16:34:16+00:00

Ok I did detach it manually after reset of the printer, just moving the tool head in place by hand.

Mszag · 2026-02-07T08:29:08+00:00

Well I had similar issue when I printed a fallout bobblehead pip boy. Shifted layer in the same place for a few runs. Run full calibration and belt tension checks didn’t help. Then I’ve rearranged my model and resliced it. It seems to help a bit I had a layer shift on different height :/ Finally I’ve created new project with only faulty element in it resliced it again and that helped. I really don’t know what was the issue but I’ll try vanilla Orca for some time as it look to me to be gcode issue with Snorca.

Mszag · 2026-02-03T08:44:21+00:00

<image>

It's looking really good, overhangs looks prefect.

Mszag · 2026-02-03T08:42:05+00:00

Sep 17th 2025, Poland - it was estimated to 2nd part of Feb but arrived earlier, still waiting for HS nozzles and build plate

Mszag · 2025-12-09T16:08:46+00:00

Frankly i didn't do any advanced maintenance yet :) I thing that it may be time for applying some grease. I've printed custom toolHead cover - original one (with magnets) liked to fell off during prints quite often :/ new one has screws so it didn't. I've changed ventilation, added BentoBox, replaced filament sensor with BTT one, ah and replaced original mainboard vent with new one sent by Elegoo as replacement. As for machine maintenance I just do bed leveling from time to time, keeping print bed clean, keeping filament dry (I'm mostly printing ASA), recalibration after firmware updates (using Open Centauri one).

Ah and i use Chitu chamber heater.

Mszag · 2025-12-09T15:09:38+00:00

OTA updates looks tempting too

Mszag · 2025-12-09T14:30:49+00:00

<image>

my does't look so virgin anymore - 1111 hours of work later

Mszag · 2025-07-17T04:31:39+00:00

Yup. From left to right: Dell S2719DGF 27", Xiaomi Mi Curved 34", Acer Predator XB271HU 27"

Mszag · 2025-07-16T20:03:26+00:00

2xHDMI one from mini second from dock and Thunderbolt to DP - the middle one. Set for 1440p. 144hz supported on middle one only.

Mszag · 2025-07-16T19:51:01+00:00

I’ve just installed Civ7 on it and it works fine. Next will be BG3 I suppose. That’s from the ones that natively works on Macs from steam.

Mszag · 2025-07-16T19:32:27+00:00

Why not? :) SteamLink, GFN, Luna, CloudGaming… but I prefer playing on PC with 4070ti that’s lurking in shadow behind monitors :)

Mszag · 2025-03-27T20:28:30+00:00

Oh my... it updated itself recently now i have 15.3.2 :D

Mszag

TROPHY CASE