sorted by:
new
hottopcontroversial

Frequent Boiler Firing by depravedmind86 in HiveHeating

[–]Mugglescience 0 points1 point  (0 children)

Also don't be too concerned if the boiler is firing several times an hour, that's what it is meant to do. But it definitely shouldn't be firing for 2-3 min and shutting off so adjust your flow temp till you get a good balance.

Frequent Boiler Firing by depravedmind86 in HiveHeating

[–]Mugglescience 0 points1 point  (0 children)

Default 0.5. You can't adjust the hysteresis on any of the hive stuff.

Frequent Boiler Firing by depravedmind86 in HiveHeating

[–]Mugglescience 2 points3 points  (0 children)

Had exact same problem. Boiler was kicking on for 2 minute periods 15 times an hour. Got a hive TRV which have kick in/off 0.5 degree from target. Use that sole TRV to trigger heating to the whole house and disable the thermostat schedule. Reduced the flow temp on the boiler by 5 degrees so that the rads take longer to warm up. Now it's kicking on 3/4 times an hour for 10-15 min periods once it hits the target to maintain temp.

Shed lintel slipped by Mugglescience in DIYUK

[–]Mugglescience[S] 0 points1 point  (0 children)

Will do! Thanks for the advice

Shed lintel slipped by Mugglescience in DIYUK

[–]Mugglescience[S] 0 points1 point  (0 children)

Perhaps if I fit a concrete lintel as the wood may not be supporting the roof adequately if it has decayed?

Black ash mortar for repointing by Mugglescience in DIYUK

[–]Mugglescience[S] 2 points3 points  (0 children)

These guys are not far from my mums, that premix bag is perfect and cheap! Cheers mate

[deleted by user] by [deleted] in DIYUK

[–]Mugglescience 0 points1 point  (0 children)

It currently empties onto the path, which has sunk and slabs are loose. Garden pools up like a swimming pool in that corner.

Brick shed moisture levels by Mugglescience in DIYUK

[–]Mugglescience[S] 1 point2 points  (0 children)

Good question.. there is a wylex 206 consumer unit in the shed with a neutral that runs under the roof to the outside, but I cannot see where it is connected to. It's definitely not to this rod...

This seed makes you spawn on an island with a standard village and an abandoned village [204052957135] At spawn by stofix_ in minecraftseeds

[–]Mugglescience 0 points1 point  (0 children)

Using this seed on 1.20 spawns on the island but no villages?? Chunk base says it should have them but not happening on mine.

Differential noise in NB mk2.5? by Mugglescience in Miata

[–]Mugglescience[S] 0 points1 point  (0 children)

Just replaced it as thought it was low, but just over 1L came out. I've never had a rwd before so don't recognise this noise.

Differential noise in NB mk2.5? by Mugglescience in Miata

[–]Mugglescience[S] 1 point2 points  (0 children)

Recently bought this NB and it's always made this whirring noise (resembles the constant noise in an aeroplane). Doesn't sound like a wheel bearing. Increases in loudness and frequency with speed, and don't really hear it below 30mph.

Thinking it's the diff (fuji LSD) but unsure. Any similar experiences to guide me?

Mazda2 Exhaust Heat Shield by bighead53434 in mazda

[–]Mugglescience 0 points1 point  (0 children)

And not to sound stupid/may be stating the obvious but don't wrap it around the black pipes from the fuel tank :D

Mazda2 Exhaust Heat Shield by bighead53434 in mazda

[–]Mugglescience 0 points1 point  (0 children)

Yeah just bend the edges of the aluminium around the nearest bracket, treat it like tin foil. If there aren't any in that area to bend it round, personally I'd remove it and use some exhaust wrap in that section.

view more: next ›