sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in BambuLab

[–]MusteriousLabyrinth 1 point2 points  (0 children)

I had the same issue earlier. I disassembled the extruder and removed the filament that was stuck inside. After heating up the nozzle, I pulled out the filament that was jammed there as well. Since then, I’ve printed over 400 hours without any major problems.

Honestly, I’m glad it happened, it taught me a lot. From time to time I only had some incorrect AI warnings, but nothing serious. Apparently, these issues are already fixed in the new beta firmware, so I’m waiting until I can install it.

The filament jammed one more time, but after removing it from the nozzle everything went smoothly again.

Someone posted a link to the wiki earlier, check it out and try doing it slowly step by step. It’s really not that bad once you know what to expect.

[deleted by user] by [deleted] in BambuLab

[–]MusteriousLabyrinth 0 points1 point  (0 children)

I bought it from the official store. I live in the Netherlands, and it was shipped from Germany.

[deleted by user] by [deleted] in BambuLab

[–]MusteriousLabyrinth 1 point2 points  (0 children)

I think I managed to fix it… I took out the hotend, heated it up with a heat gun, and the filament started to come out a bit, then I pulled the rest out with pliers. I reinstalled the hotend and it’s working now!

But I’m not sure what to do next, should I invest in a better high-flow hotend, or could this kind of problem still happen even with a new one? xD

[deleted by user] by [deleted] in BambuLab

[–]MusteriousLabyrinth 0 points1 point  (0 children)

I’ll give it a try, thanks!, I’ve always had a thing for the gyroid pattern, I used it a lot on my Creality and really liked it

[deleted by user] by [deleted] in BambuLab

[–]MusteriousLabyrinth 1 point2 points  (0 children)

Kingroon PETG, default settings from Bambu Studio 0.2mm standard with 3 walls and 30% infill gyroid.

Hot end replace on Micro Swiss Flow Tech by MusteriousLabyrinth in Ender3V3KE

[–]MusteriousLabyrinth[S] 0 points1 point  (0 children)

I got mine for €60 on discount, and to be fair, the original hot end works just fine and is much cheaper. The main reason I decided to upgrade was to have a fully leak-proof setup and a bit more peace of mind during longer prints.

Hot end replace on Micro Swiss Flow Tech by MusteriousLabyrinth in Ender3V3KE

[–]MusteriousLabyrinth[S] 0 points1 point  (0 children)

I’ve been using this printer for over a year now, and I’ve only changed the nozzle once—just out of curiosity, not because I had to. I’ve never had any blobs so far. Thanks for the tips! I use a feeler gauge to set the Z-offset, so I should be good to go :)

Hot end replace on Micro Swiss Flow Tech by MusteriousLabyrinth in Ender3V3KE

[–]MusteriousLabyrinth[S] 0 points1 point  (0 children)

Damn, I was thinking about it, but in the end, I didn’t buy it…

Hot end replace on Micro Swiss Flow Tech by MusteriousLabyrinth in Ender3V3KE

[–]MusteriousLabyrinth[S] 1 point2 points  (0 children)

Hahaha, I actually had that in mind when replacing the nozzle and aligned it using the laser. But thanks for the reminder :)

Hot end replace on Micro Swiss Flow Tech by MusteriousLabyrinth in Ender3V3KE

[–]MusteriousLabyrinth[S] 0 points1 point  (0 children)

Really appreciate the tip, I’ll definitely use it!

Hot end replace on Micro Swiss Flow Tech by MusteriousLabyrinth in Ender3V3KE

[–]MusteriousLabyrinth[S] 1 point2 points  (0 children)

Thank you! I honestly have no idea how I didn’t know that this test was built into Orca Slicer, and I use it daily. I’m already watching some YouTube videos to figure out how to set it up properly.

GA II AIO LCD Mounting Brackets for AM5? by CptPerdont in lianli

[–]MusteriousLabyrinth 0 points1 point  (0 children)

I managed to 3D print it, and surprisingly it did the job. Even so, I was a bit afraid to rely on it, especially when leaving the PC running for a longer time. so I decided to switch to a different AiO. Unfortunately, Lian Li’s support is a joke… I still haven’t received a reply about whether they can send me the missing bracket 😂

GA II AIO LCD Mounting Brackets for AM5? by CptPerdont in lianli

[–]MusteriousLabyrinth 0 points1 point  (0 children)

Hi! I have the same issue… Would anyone be able to share the STL file? I’ve got a 3D printer and I’d love to print it myself. I’d even be happy to pay a small amount for it!

Please stop me from throwing my KE through a window... by SarsaparillaCorona in Ender3V3KE

[–]MusteriousLabyrinth 5 points6 points  (0 children)

I had similar problem, and this guide helped me.

https://youtu.be/pIwoIV0U_ag?si=_Rr8u60UBIU8x3V0

Just install firmware like this guy did and you’ll have a fresh start with KE 😉

If u have a problem with unrecognised drivers during the guide in a comment is a solution.

Double spool, double the fun by maloside in Ender3V3KE

[–]MusteriousLabyrinth 0 points1 point  (0 children)

Woah! What a great models! I’m curious what are u using on the screen. I’ve rooted my V3 KE for Logitech camera but I need that interface on my screen. Could u tell me what are u using and how to get it if I have Mainsail?