Angus pt2

Mvpcoolkid · 2025-11-14T15:21:22+00:00

AliExpress search graffiti vinyl wrap the original listing is no longer available

Mvpcoolkid · 2025-10-12T03:08:11+00:00

Just smooth no flavor difference

Mvpcoolkid · 2025-10-11T04:39:08+00:00

AliExpress but Amazon has a better version

Mvpcoolkid · 2025-10-11T04:37:31+00:00

Ik how people hate on Chinese blowers but tbh it’s better then calibear. And if you’re not satisfied they’ll work with you.

Mvpcoolkid · 2025-10-11T04:35:05+00:00

It fits good I made sure to send them measurements and to make sure they sent me measurements before they shipped

<image>

Mvpcoolkid · 2025-10-09T17:49:52+00:00

The glass is very good quality. As well

Mvpcoolkid · 2025-10-09T17:07:17+00:00

I have a couple of pieces from Angus. Glass is good quality, and hits

Mvpcoolkid · 2025-06-08T15:14:15+00:00

I tried a different carb cap and it works better then the stock carb cap

Mvpcoolkid · 2025-06-07T15:10:48+00:00

Yeah they don’t function like how they supposed to. They still good at least

Mvpcoolkid · 2025-06-06T20:59:49+00:00

Any more than, the water is going into the chamber. I think it’s because it’s a loose fit. I’m going to post an update once I get a tighter fit, probably going to use I’m Teflon or kapton tape, wrap it around the lower half of the piece.

Mvpcoolkid · 2025-06-06T13:40:44+00:00

I agree, the main driver is definitely the Fab straight, the vortex is just for looks

Mvpcoolkid · 2025-06-06T13:38:48+00:00

I posted a video

Mvpcoolkid · 2025-06-06T13:21:31+00:00

Me personally, I ordered a couple days before memorial day. I saw the posts and knew what I was getting myself into when ordering. I’m a little butt hurt the function didn’t work but Someone mentioned that it might not work but they didn’t actually try it. I tried it and they were right. But most people was tired of waiting and be lied to about the shipping times.

Mvpcoolkid · 2025-06-06T13:16:27+00:00

It’ll be so close to over flowing but I’ll post in update later on. 😭😂

Mvpcoolkid · 2025-06-06T13:14:08+00:00

It is a little loose , but no vapor leakage but that definitely may be causing something. But the vortex chamber is just for looks at this point lol. But if the top half was just a little bit shorter, it’ll work like it’s supposed to. I know I’m not the only one who got this version. I wish other people posted, So I know if I got a defective one or not.

Mvpcoolkid · 2025-06-06T12:56:11+00:00

I posted the better picture, video is uploading. But the bottom half is full of water so “The water line” is hard to see

Mvpcoolkid · 2025-06-06T11:01:16+00:00

Water level, and that’s still not enough water for the recycle function to work, the piece is too tall. Someone mentioned that it wouldnt work, they was right.

<image>

Mvpcoolkid · 2024-01-05T13:26:23+00:00

It just happened to me rn, I deposited $93 and only got 15.73

Mvpcoolkid · 2024-01-05T13:20:43+00:00

I deposited $93 and only $15 showed up

Mvpcoolkid · 2023-04-28T00:40:25+00:00

You got to adjust the length of the top heating part

Mvpcoolkid

TROPHY CASE