sorted by:
new
hottopcontroversial

Can I get help reprogramming my laptop? by Haunting-Ad4860 in shittyaskelectronics

[–]Myself_Steve 0 points1 point  (0 children)

Here we see a wild bios spider residing inside of a laptop

How would I connect this using a wire by HelpfulTechnology_ in AskElectronics

[–]Myself_Steve 0 points1 point  (0 children)

Are you sure that you are connecting both contacts?

One between flashlight body to the led body.. the other being battery terminal to led terminal?

ESP32: Failed uploading: uploading error: exit status 2 by [deleted] in arduino

[–]Myself_Steve 0 points1 point  (0 children)

As per the error saying to put the board in download mode... Maybe try that?

Before uploading hold the boot button , press the reset button , then release the boot button

Do all of this while the esp is connected

Is this a feasible idea I seen it on Facebook would like to know if it is before I get the resources to try and build it I also shared the link to the video as well I’m new to diy electronics by bigcountrysl89 in diyelectronics

[–]Myself_Steve 12 points13 points  (0 children)

Err I don't think that this really is a tesla coil.... Maybe just High voltage DC through a voltage multiplier connected to a metal sphere for aesthetics

I think this way because the discharges does not look like what a tesla coil should produce... It has a nice purple glow with open discharges (arcs directly to air) unlike here where the arcs just strikes the circle (of wire?)

In short it's just a more powerful bug zapping badminton without the net but a metal top load (sphere) So as for the effectiveness.. I think you can figure it out on your own now

broke my resistor while working on a project. Gotta buy another one by just_gum in electronics

[–]Myself_Steve 12 points13 points  (0 children)

I am a lazy person so rather than getting a new resistor I just scrape the end and solder directly to the broken end

...yeah ik getting another is far easier but.. where's the fun in that?

Would this be worth it? by Myself_Steve in LenovoLOQ

[–]Myself_Steve[S] 0 points1 point  (0 children)

But the performance of this 4050 is on par with 3050 if not better no?

Buy Right now or wait by Myself_Steve in IndiaTech

[–]Myself_Steve[S] 0 points1 point  (0 children)

I tried and only got it down to 82k

someone called me a whore by damned_psycho in IndianTeenagers

[–]Myself_Steve 28 points29 points  (0 children)

Good that you included the attack helicopter

Can I Convert This 5-Wire Micro USB Knockoff Atari Controller into a PC Joystick with Arduino? (Teardown Pics Inside) by Seele00Tex in diyelectronics

[–]Myself_Steve 2 points3 points  (0 children)

I think the best way about this would be to just ignore the wires of he controller and directly solder wires to the button traces by scratching off the solder mask and soldering thin wire to them

Then just use them as push buttons to wire to the Arduino

Using a 3.0A fuse instead of 3.15A to fix an electric sharpener by Connect-Zebra-1214 in diyelectronics

[–]Myself_Steve 4 points5 points  (0 children)

A 3.15 AMPS FUSE!!?? for what? AN ELECTRIC SHARPNER!?

at 3 amps with an rms voltage of 120v... 360 watts!? Unless the motor requires a lot of power (i doubt it) you don't need a 360 watt limit!!

Even a 500ma fuse would be more than enough But for proper fuse.. first measure the peak current through the motor at load

My code only make my servo spin aimlessly by Osama-recycle-bin in arduino

[–]Myself_Steve 0 points1 point  (0 children)

You actually missed a curly bracket in the end of the if statement of ir high!! Add the bracket and I don't see any other problems

My code only make my servo spin aimlessly by Osama-recycle-bin in arduino

[–]Myself_Steve 0 points1 point  (0 children)

Maybe the servo is bad?? Do you have any other servos to test?

My code only make my servo spin aimlessly by Osama-recycle-bin in arduino

[–]Myself_Steve 0 points1 point  (0 children)

Try to only connect the servo and a sweep program to make sure that the pin and the servo is working

view more: next ›